Specifications for GENESYS 10

GENESYS 10 Vis

GENESYS 10 UV

GENESYS 10 UV

Scanning

Spectral Bandwidth

5nm

5nm

Optical System

Single-beam, grating-

based, single detector

Split-beam, grating-based,

dual detectors

Lamp Source;

Lifetime

Tungsten-halogen;

1000 hours typical

Xenon-, 5 years typical

Wavelength:

Range

325 - 1100nm

190 - 1100nm

Accuracy

± 1.0nm

Repeatability

± 0.5nm

Display

320 x 240 pixel backfit LCD, 3.8" x 2.8"

Photometric:

Range

0.3 - 125%T; -0.1 - 3.0A-1 0 - 9999C

Readout

Absorbance, Transmittance, Concentration

Accuracy ²

0.5% OR 0.005A whichever is greater up to 2A

Noise

≤ 1 mA at 0A; ≤ 2mA at 2A, peak-to-peak

Drift

≤ 2mA/hour

after warmup

≤1 mA/hour

Stray Light3

≤ 0.1 %T at 340

and 400nm

≤ 0.1 %T at 220, 340 and 400nm

Standard Interface

Bi-directional RS232C

Bi-directional RS232C;

parallel output in PCL

format

Cell Holder

1-position OR automatic 6-position cell holder

Keyboard

Membrane keypad

Software

Absorbance/Transmittance/Concentration,

Standard Curve, Absorbance

Ratio, Absorbance Difference, Kinetics,

Survey Scan, 3-Point Net, Multiwavelength,

Performance Validation

As G10 UV but with fullrange scanning

Scanning speed: 200-

1000nm/min

Sampling interval: 1, 2,

3, 5nm

Test Storage

Up to 40 sets of test parameters

Langvages

Software and Printout: English, French, German, Spanish, Italian

(user selectable)

Operator's Manual: English, French, German, Spanish, Italian

Printer (optional)

40-column internal graphics

40-column internal

graphics; external HP

PCL printer

Analog Output

(optional)

0 - 1V for -0.1 to 2.5A

Not available

Power Requirements

Selected automatically; 100 - 240 Volts

Dimensions

330W x 410D x 235H mm (13" x 16" x 9")

Weight

8.6 Kg (19lb)

¹ These specifications are valid only after a 30-minnte warm-up period (Vis unit only) and when the required environmental conditions (nee below) are met.

² Measured using NIST 930D filtern

³ 220nm, 340nm and 400nm measurements with SPECTRONIC Standards (#333150)

Environmental and electrical requirements (meets the IEC 1010-1 international safety standard)

Line voltages

100 - 240 VAC ±10%

50 - 60 Hz

80 VA max

Operating environment

The instrument meets the specifications an the previous page under the following conditions after a 30-minute warm-up period.

Ambient temperature - 5° to 40° C

(23° F to 104° F)

Relative humidity - 20% - 80% RH

Storage environment

-20° C to 70° C (24.8° F to 158° F) Relative humidity not to exceed 0.040 pounds moisture per pound of dry air. Allow instrument to adjust to room temperature for 24 hours after taking it out of storage.

Temperature should be maintained at ±4° F.

Relative humidity should be maintained to ±5%.

Attitude

From below sea level to 2000 meters

(6562 feet)

For indoor use only

Installation Category II

Pollution Degree 2