Beckman SW 55Ti
- Mehr Informationen
- Status, Liefer- und Zahlungsbedingungen
- Technische Spezifikationen
- Weitere Produkte
Objektnummer | B00014083 |
---|---|
ID-Nummer | 014083 |
Objektbezeichnung | Beckman SW 55Ti |
Status | Archiv |
Status, Liefer- und Zahlungsbedingungen
Geräteüberprüfung
Die gebrauchten Laborgräte werden vor der Auslieferung von der Labexchange Service GmbH überprüft. Sie erhalten voll funktionsfähige Geräte.
Versandzeit
Die angegebenen Versandzeiten sind die jeweils kürzesten für einen Artikel. Die tatsächlich Versandzeiten können im Einzelfall davon abweichen. Die endgültigen Versandzeiten werden in der Auftragsbestätigung angegeben.
Bei Bestellung/Anfrage von mehreren Artikeln bieten wir grundsätzlich Sammellieferung an. Die Versandzeit berechnet sich nach der Position mit der längsten Versandzeit. Auf ausdrücklichen Wunsch ist eine Teillieferung möglich.
Versandarten
Paketdienste, Speditionen, Selbstabholung, Lieferung durch Labexchange-Fuhrpark
Lieferinformationen
Unsere Lieferbedingungen sind grundsätzlich zzgl. Versandkosten. Angegebene Versandkosten sind zu erwarten. Falls anfallende Versandkosten nicht angegeben sind, fragen Sie diese bitte gesondert an.
Die angegebenen Fracht- und Verpackungskosten beziehen sich auf den günstigsten Transportweg und sind vorbehaltlich unvorhergesehener Kostensteigerungen. Durch unvorhersehbare Ereignisse können sich die Frachtraten und die Lieferzeiten jederzeit ändern und müssten der aktuellen Situation angepasst werden. Incoterm-Kodierung gemäß Incoterms 2010: Bei Selbstabholung EXW, bei Sendungen per Schiff CFR, per Luftfracht CPT, übrige Sendungen DAP. Hinweis für Auslandssendungen: Ein Präferenznachweis/EUR1 wird von uns nicht ausgestellt. Bei Selbstabholung/EXW aus Drittländern und der EU werden 16% MWSt als Kaution einbehalten bis wir die Gelangensbestätigung/den Verbringungsnachweis des Käufers erhalten haben.
Zahlungsbedingungen
Wir akzeptieren keine Zahlung per Letter of Credit, PayPal etc. Der Rechnungsbetrag ist in jedem Fall ohne Abzug fällig. Die Ware bleibt bis zur vollständigen Bezahlung unser Eigentum. Skonto wird nicht gewährt.
Land |
Mögliche Zahlungsarten |
Bemerkung |
DE, AT, CH |
Rechnung, Vorkasse, Kreditkarte |
Eine Zahlung per Rechnung ist nur für Firmenkunden möglich. |
NL, BE, LU |
Rechnung, Vorkasse, Kreditkarte |
Eine Zahlung per Rechnung ist nur für Firmenkunden möglich. |
Alle weiteren Länder |
Vorkasse, Kreditkarte |
|
Es gelten unsere Allgemeinen Verkaufs-, Lieferungs- und Zahlungsbedingungen. Diese finden Sie hier. Zwischenverkauf, sowie Irrtum und Preisänderungen sind vorbehalten.
Statusdefinition
Alle Artikel sind gebrauchte Artikel, es sei denn ein Artikel wird explizit als Neugerät aufgeführt.
Status |
Zustand |
Bemerkung |
Sofort verfügbar |
gebraucht |
Der Artikel wurde bereits überprüft und befindet sich in einem einwandfreien Zustand. Er kann direkt an Sie versendet werden. |
Lagergerät |
gebraucht |
Der Artikel befindet sich in unserem Lager. Unsere Techniker werden den Artikel vor der Auslieferung überprüfen. Sie erhalten voll funktionsfähige Artikel. |
Anbieter |
gebraucht |
Der Artikel befindet sich noch beim Anbieter. Nach Ihrer Bestellung wird er von uns angekauft, überprüft und an Sie versendet. Ein Funktionszertifikat und ein Servicebericht sind bei der Lieferung enthalten. |
Neugerät |
neu |
Es handelt sich um einen fabrikneuen Artikel. Es gelten die Garantiebestimmungen des Herstellers sowie die gesetzliche Gewährleistungsfrist. |
Labprocure |
gebraucht |
Verantwortlich für den Inhalt dieses Geräteangebotes ist die Labprocure GmbH als Geräteinserent. Labprocure übernimmt die Haftung für die hier inserierten Angebote und für die beinhalteten Fotos und Angebotstexte. Labprocure GmbH, Bruckstrasse 58, 72393 Burladingen. |
Firma: Beckman
The following illustrations and descriptions are referring to the instrument model and are drawn from brochures. They are not representing the delivery volume. The exact delivery content you will find only in the offering text.
SW 55 Ti ROTOR
(for use in Beckman Class B, C, D, F, G, H, Q, R, and S Preparative Ultracentrifuges)
DESCRIPTION
The SW 55 Ti swinging bucket rotor, rated for 55 000 rpm, is used in Beckman class B, C, D, F, G, H, Q, R, and S preparative ultracentrifuges. This rotor is designed to generate centrifugal forces for mang applications: concentrating viruses; separating DNA, RNA, or low molecular weight proteins in density gradients; and banding RNA-containing viruses in sedimentation equilibrium studies. Approximate sample volume per tube is 0.2 mL, with a gradient volume of about 4.8 mL.
The rotor body and buckets are made of titanium finished with polyurethane paint; the rotor body is black and the buckets are red. The aluminum handle and bucket caps are red anodized for corrosion resistance. The red SW 55 Ti buckets are similar in size to the black SW 50.1 buckets. DO NOT interchange the two types of buckets.
The bucket and cap assemblies hock over the Grossbar of the rotor hanger mechanism. Bucket 0-rings made of Buna N rubber maintain atmospheric pressure inside the buckets during centrifugation. Drive pins in the rotor drive hole prevent slippage of the rotor relative to the Instrument drive hub during acceleration and deceleration. In class G, H, R, and S Instruments, speeds exceeding 55 000 rpm are detected by means of an oversp,-led disk attached to the rotor bottom.
The SW 55 Ti rotor is warranted at maximum speed for 1000 runs, 2500 hours of centrifugation, or 5 years, whichever occurs first. If, after 1000 runs or 2500 hours of centrifugation, the 5-year warranty period has not expired, the warranty is then extended for an additional 1000 runs, or 2500 hours of centrifugation at any speed up to 90 percent of maximum.
SPECIFICATIONS
Maximum speed 55 000 rpm
Maximum solution density
1.2 g/mL
Relative Centrifugal Field* at maximum speed
At rmax (108.5 mm) 368 000 x g
At rav (84.6 mm) 287 000 x g
At rmin (60.8 mm) 206 000 x g
k factor at maximum speed (full tubes)
48
k" factors at max. speed (5 to 20% sucrose gradient; 5°C)
When particle density = 1.3 g/mL 135
When particle density = 1.5 g/mL 123
When particle density = 1.7 g/mL 118
Number of buckets 6
Available tubes see Tables 1 and 2
Nominal tube dimensions (largest tube) 1/2 x 2 in. (13 x 51 mm)
Nominal tube capacity 5 mL
Nominal rotor capacity
30 mL
Approximate acceleration time to maximum speed
(fully loaded, in L8M ultracentrifuge)
3 min
Approximate deceleration time from maximum speed
(fully loaded, in L8M ultracentrifuge) 3 min
Weight of fully loaded rotor 5 kg (11 lb)
Conditions requiring speed reduction see RUN SPEEDS
Rotor material titanium
-------------------------------
*Relative Centrifugal Field (RCF) is the ratio of the centrifugal acceleration at a specified radius and speed ( rw 2 ) to the standard acceleration of gravity (g) according to the following formula:
where r is the radius in millimeters, w is the angularvelocity in radians per second (2πRPM/60), and g is the standard acceleration of gravity (9807mm/s 2 ). After substitution:
TUBES
Tubes available for the SW 55 Ti rotor are listed in Tables 1 and 2. Be sure to observe the maximum speed Limits shown, and use only the tubes listed.
Temperature Limits
Polyallomer and polycarbonate tubes haue been tested for use at temperatures between 2 and 25°C, and Ultra-Clear TM tubes at temperatures between 4 and 20°C. Before use at other temperatures, these tubes should be tested under simulated run conditions. Polyallomer tubes should not be centrifuged below 2°C, as they may become brittle and Crack. Stainless steel tubes can be centrifuged at any temperature.
Filling and Sealing Tubes
Thinwall polyallomer and Ultra-Clear tubes should be filled to within 2 or 3 mm of the top for proper tube support. Thickwall tubes should be half-full to within 2 or
3 mm of the top for centrifugation. Stainless steel tubes can be filled to any level for centrifugation; however, opposing tubes should be filled to the saure level.
Quick-Seal tubes should be filled almost to the base of the neck. Do not leave
a large air space. Too muck air can cause the tube to deform, which may disrupt gradients or sample. Quick-Seal tubes are heat sealed, and spacers are required on top of the tubes when they are loaded into the rotor. See the instruction
bulletins on "How to Use Quick-Sea19 Tubes" (IN-163 and IN-181) for filling and sealing these tubes.
The g-Max TM system uses a combination of short bell-top Quick-Seal tubes and floating spacers (also referred to as g-Max spacers). Because Quick-Seal tubes are heat sealed they provide a secondary means of containment, making this system especially useful for centrifuging biohazardous or radioactive samples. Finally, the shorter pathlength of these tubes permits shorter run times. For more Information on the g-Max system, see publication DS-709.
Table 1. Available 1/2-in. Diameter Tubes for the SW 55 Ti Rotor
Only tubes listed either in this table or in Table 2 should be run in this rotor
Description |
Dimensions, (Inches) |
Part Number |
Maximum Volume (mL) |
Maximum Speed (rpm) |
Quick-Seal polyallomer* |
1/2 x 1 |
345829 |
2 |
55 000 |
Ultra-Clear |
112 x 2 |
344057 |
5 |
55 000 |
polyallomer |
112 x 2 |
326819 |
5 |
55 000 |
thickwall polyallomer |
112 x 2 |
349623 |
3.5 |
55 000 |
thickwall polycarbonate |
1/2 x 2 |
349622 |
3.5 |
55 000 |
Quick-Seal konical ** |
1/2 x 2 |
358647 |
3.2 |
55 000 |
konical *** |
1/2 x 2 |
358119 |
3 |
55 000 |
stainless steel |
1/2 x 2 |
305588 |
5 |
**** |
*Use floating spacer, p/n 355535, with this tube. Floating spacers, part of the g-Max system of tube Support, are made of Noryl, a registered trademark of General Electric.
** Use adapter, p/n 358153, and floating spacer, p/n 355535, with this tube.
***Use adapter, p/n 358153, with this tube.
****Read the section on RUN SPEEDS before using this tube.
Thinwall polyallomer konical TM tubes can also be used for pelleting Separations in the SW 55 Ti rotor. These tubes haue a conical tip to reduce working volume and minimize gradient chemical requirements, and come in both open-top and Quick-Seal designs. conical-cavity adapters hold the tubes in the rotor buckets.
See publication LR-IM for the care, cleaning, and chemical resistance of tubes and of rotor components.
Table 2. Smaller Tubes for the SW 55 Ti Rotor Only tubes listed
either in this table or in Table 1 should be run in this rotor
Description |
Dimensions and Volume |
Part Number |
Required Adapter |
Maximum Speed and RCF |
k Factor |
Ultra-Clear |
3/16 x 1 5/8 in. (0.8 mL) |
344090 |
356860 305527 |
48 000 rpm 269 000 x g 25 000 rpm 73 200 x g |
64 209 |