TA Instruments AR 500
Objektnummer | B00014614 |
---|---|
Seriennummer | 014614 |
Object Naam | TA Instruments AR 500 |
Status | Archiv |
Status, leverings- en betalingsvoorwaarden
Apparatuurcontrole
De gebruikte apparatuur wordt voorafgaand aan levering gecontroleerd door Labexchange Service GmbH. U ontvangt volledig functionerende apparatuur.
Verzending
De vermelde verzendtijden zijn telkens de kortste voor een artikel. In bepaalde gevallen kunnen de daadwerkelijke verzendtijden daarvan afwijken. De uiteindelijke verzendtijden worden aangegeven in de opdrachtbevestiging.
In de regel bieden we combinatieleveringen aan. Levertijden zijn afhankelijk van het artikel met de langste levertijd. Deelleveringen zijn mogelijk tegen een toeslag.
Verzendmethoden
Koeriersdiensten, transportbedrijven, zelf afhalen, levering door Labexchange wagenpark
Informatie levering
De prijzen zijn exclusief verzendkosten. De genoemde verzendkosten zijn de te verwachten kosten. Afwijkingen zijn mogelijk. In het geval geen kosten voor verzending zijn gespecificeerd, vraag die dan afzonderlijk aan.
De opgegeven vracht- en verpakkingskosten hebben betrekking op de goedkoopste transportroute en zijn onder voorbehoud van onvoorziene kostenstijgingen. Door onvoorziene gebeurtenissen kunnen vrachttarieven en levertijden op elk moment veranderen en moeten ze worden aangepast aan de huidige situatie. Incoterm coderingen volgens Incoterms 2010: Bij afhalen EXW, CFR voor zendingen over zee, CPT per luchtfracht, andere zendingen DAP. Opmerking: We geven geen preferentieel certificaat/EUR1 af. Bij zelf afhalen/af fabriek (EXW) uit derde landen en de EU wordt 16% btw als borg ingehouden, tot we de ontvangstbevestiging/het leveringscertificaat van de koper hebben ontvangen.
Betalingsvoorwaarden
Wij accepteren geen betalingen Letter of Credit, PayPal etc. Het factuurbedrag is volledig verschuldigd. Er zijn geen betalingskortingen. De goederen blijven tot volledige betaling ons eigendom.
Land |
Mogelijke betaalmethoden |
Opmerking |
Duitsland, Oostenrijk, Zwitserland |
Betaling via factuur, vooruitbetaling, per creditkaart |
Betaling via factuur is mogelijk voor ondernemingsklanten. |
Nederland, België en Luxemburg |
Betaling via factuur, vooruitbetaling, per creditkaart |
Betaling via factuur is mogelijk voor ondernemingsklanten. |
Andere landen |
vooruitbetaling, per creditkaart |
|
Onze Algemene Voorwaarden voor Verkoop, Levering en Betaling zijn hierop van toepassing. Deze voorwaarden zijn hier te downloaden.
Tussenverkoop is ons voorbehouden.
Beschrijving status:
Alle artikelen zijn gebruikte artikelen, tenzij bij een artikel uitdrukkelijk wordt vermeld dat het om een nieuw apparaat gaat.
Firma: TA Instruments
The following illustrations and descriptions are referring to the instrument model and are drawn from brochures. They are not representing the delivery volume. The exact delivery content you will find only in the offering text.
The TA Instruments AR Rheometers are fifthgeneration instruments, which functions as either a controlled-stress or controlled-rate Instrument.
The rheometers are designed to fulfill the requirements of measurement as implied by the füll meaning of the term rheologydefined as the "study of the deformation and flow of matter."
Deformation is measured in the non-destructive region of elastic or visco-elastic deformation. This can give invaluable Information concerning the microscopic interactions in the test material, as well as measuring the shear stress/shear rate relationships at higher Stresses.
In the controlled-stress technique, the stress can be applied and released at will, and the actual behavior of the Sample can be measured directly. This is not usually possible wich conventional controlled-shear rate instruments. In addition, most real-life situations can be simulated more accurately using controlled-stress measurements.
Instrument Components
The Instrument consists of a main unit mounted on a cast metal stand, with the electronic control circuitry contained within a separate electronics control box. Figure 2.3 Shows the front and rear of the electronics control box.
The AR Rheometer contains an electronicallycontrolled induction motor with an air bearing Support for all the rotating parts. The drive motor is equipped with a hollow spindle, with a detachable draw rod inserted through it. The
draw rod has a screw-threaded section at the bottom, which allows the geometry to be securely attached.
The measurement of angular displacement is dope by an optical encoder deviee. This can detect very Small movements down to 0.6 prad. The encoder consists of a non-contacting light source and photo-cell, arranged either side of a transparent disc attached to the drive shaft. On the edge of this disc are extremely fine, accurate photographically-etched radial lines. Therefore, this is a diffraction grating. There is also a stationary Segment of a similar disc between the light source and encoder disc. The interaction of these two discs results in diffraction patterns that are detected by the photo cell. As the encoder disc moves when the sample strains under stress, these patterns change. The associated circuitry interpolates and digitizes the resulting Signal to produce digital data. This data is directly related to the angular deflection of the disc, and, therefore, the strain of the sample.
The main electronics are housed in a separate control box. The interplay between the rheometer/electronics and Controller are explained in more detail in Chapter 5.)
Temperature control is achieved in the Standard configuration via a Peltier plate System.
Technical Specifications
Dimesions
AR-N Instrument Section (Casting):
Width: 9 in. (22cm)
Height: 23,5 in. (60cm)
Depth: 10 in. (25 cm)
Weight: 48.5 lbs (22 kg)
AR-N Controller:
Width: 7,5 in (18.5 cm)
Height: 14,5 in. (37 cm)
Depth: 17 in. (43 cm)
Weight: 46,2 lbs (21 kg)
Supply Voltage 230 Vac 5 amps
120 Vac 10 amps
Frequency 50 to 60 Hz
Power 800 Vac
Torque 0.1 µNm to 100 mNm (AR 1000)
Range 1µNm to 50mm (AR 500)
Shear Stress 0.0008 to 508,000 Pa (AR 1000)
Range (Geometry 0.008 to 254,000 Pa (AR 500)
Dependent)
Frequency 0.1 mHz to 100 Hz (AR 1000)
Range (0.628 mrad s -1 to 628 rad s -1 )
0.1 inHz to 40 Hz (AR 5 00)
Angular Controlled Stress:
Velocity 10 -8 to 100 rad s -1
Range Controlled Strain:
10 -2 to 100 rad s -1
Angular 0.62 µrads
Displacement
Resolution
Shear Rate Range 10 -6 to 11,000 s -1
(Geometry, material
and technique
dependent.)
Minimum strain 0.00006
Normal force
Range: 1 g to 5000 g
Peltier System Specifications
Peltier Standard: -10 °C to 99 °C
System Extended: -20 °C to 180 °C
Range
NOTE: Extended use of the extended Peltier plate is not recommended above 150 °C. Also, the lower temperature ramps can be significantly reduced by circulating an appropriate refrigerant.
Ramp Rate 20 °C min -1
(Standard)
(Typical)
Ramp Rate (20 to 100 °C) 50 °C min -1
(Extended) (100 to 150 °C) 25 °C min -1
Internal 0.016 °C
Resolution
of Pt100
Optional Accessory Specifications for Extended Temperature Module (ETM)
ETM Temperature
Range -100 °C to 400 °C
Ramp Rate
(Typical) 120 °C min -1
Internal
Resolution 0.025 °C