JavaScript lijkt te zijn uitgeschakeld in uw browser. Voor de beste gebruikerservaring, zorg ervoor dat javascript ingeschakeld is voor uw browser.
Garantieservices
Optionele garantieverlenging tot een jaar
Optionele installatie van apparatuur voor onmiddellijk en betrouwbaar gebruik
Aantrekkelijke huur- en leasingaanbiedingen om uw budget te sparen
Vragen over dit apparaat en gratis terugbellen
Garantie:Alle gebruikte apparatuur wordt vóór levering aan een test en/of revisie onderworpen en wordt alleen dan geleverd als die perfect functioneert. De test en daaruit gebleken goede functionering worden bevestigd in een door een onafhankelijk servicebedrijf opgesteld servicecertificaat. De Labexchange Fullguarantee bedraagt 60 dagen. (Geldig voor landen binnen de EU en CH)Functioneringscertificaat:Zowel de test als het goede functioneren van het apparaat worden, behalve in het servicecerapport, gedocumenteerd in het functioneringscertificaat.24 maanden waarborg:De waarborgtermijn voor onze apparaten bedraagt 24 maanden vanaf leveringsdatum.
Indien gewenst nemen we de mogelijkheid voor verlenging van de garantietermijn van uw apparaat in overweging. Als het mogelijk is, bedraagt de garantietermijn 6 maanden voor een meerprijs van 10% over de catalogusprijs en 1 jaar bij een meerprijs van 20%. (Geldig voor DE, AT, CH, FR, NL, BE, LU, GB en IR)
Speel op zeker! Het doet ons genoegen u de installatie van uw laboratoriumapparatuur aan te kunnen bieden. Onze gekwalificeerde technici installeren het apparaat op de door u gewenste datum in het laboratorium. U kunt zo snel en veilig aan het werk met uw nieuwe laboratoriumapparatuur.
De installatie van apparatuur door Labexchange brengt ook andere voordelen met zich mee. U krijgt op die manier een garantieverlenging tot 3 maanden en heeft bovendien recht op de Labexchange Terugkoopgarantie.
Kwetsbare laboratoriumapparatuur en analysesystemen, evenals veel van de beschikbare laboratoriumkappen, zijn al inclusief installatie.
* Verplichte velden
De gebruikte apparatuur wordt voorafgaand aan levering gecontroleerd door Labexchange Service GmbH. U ontvangt volledig functionerende apparatuur.
De vermelde verzendtijden zijn telkens de kortste voor een artikel. In bepaalde gevallen kunnen de daadwerkelijke verzendtijden daarvan afwijken. De uiteindelijke verzendtijden worden aangegeven in de opdrachtbevestiging.
In de regel bieden we combinatieleveringen aan. Levertijden zijn afhankelijk van het artikel met de langste levertijd. Deelleveringen zijn mogelijk tegen een toeslag.
Koeriersdiensten, transportbedrijven, zelf afhalen, levering door Labexchange wagenpark
De prijzen zijn exclusief verzendkosten. De genoemde verzendkosten zijn de te verwachten kosten. Afwijkingen zijn mogelijk. In het geval geen kosten voor verzending zijn gespecificeerd, vraag die dan afzonderlijk aan.
Voor levering in landen buiten de EU wordt voor export een toeslag van € 70,00 in rekening gebracht. Opmerking: We geven geen preferentieel certificaat/EUR1 af. Bij zelf afhalen/af fabriek (EXW) uit derde landen en de EU wordt 16% btw als borg ingehouden, tot we de ontvangstbevestiging/het leveringscertificaat van de koper hebben ontvangen.
Wij accepteren geen betalingen per creditkaart, Letter of Credit, PayPal etc. Het factuurbedrag is volledig verschuldigd. Er zijn geen betalingskortingen. De goederen blijven tot volledige betaling ons eigendom.
Land
Mogelijke betaalmethoden
Opmerking
Duitsland, Oostenrijk, Zwitserland
Betaling via factuur, vooruitbetaling
Betaling via factuur is mogelijk voor ondernemingsklanten.
Nederland, België en Luxemburg
Andere landen
vooruitbetaling
Onze Algemene Voorwaarden voor Verkoop, Levering en Betaling zijn hierop van toepassing. Deze voorwaarden zijn hier te downloaden.
Tussenverkoop is ons voorbehouden.
Alle artikelen zijn gebruikte artikelen, tenzij bij een artikel uitdrukkelijk wordt vermeld dat het om een nieuw apparaat gaat.
Status
Conditie
Onmiddellijk verkrijgbaar
gebruikt
We hebben het artikel in ons magazijn. Onze technici zullen het artikel voorafgaand aan levering controleren. U ontvangt volledig functionerende artikel.
Het artikel is nog bij de aanbieder. Na uw bestelling wordt het door ons aangekocht, gecontroleerd en aan u verstuurd. Een functioneringscertificaat en een servicerapport zijn bij de levering inbegrepen.
Nieuw
nieuw
Dit is een artikel dat nieuw van de fabriek komt. Hiervoor gelden de garantiebepalingen en wettelijke garantietermijn van de fabrikant.
manufacturer : Perkin Elmer
model : TurboMatrix 110
annotation : Dokumente engl.
The following illustrations and descriptions refer to the instrument model and are drawn from brochures. They do not represent the scope of delivery. Please refer to the text of the offer for the exact scope of delivery.
For added flexibility to meet your laboratorys changing requirements, five different PerkinElmer" TurboMatrix" Headspace (HS) sampler models are available:
TurboMatrix HS 16 16 vials with overlapped thermostatting of one vial.
TurboMatrix HS 40 40 vials with intelligent, overlapped thermostatting of up to 12 vials. TurboMatrix HS 110 110 vials with intelligent, overlapped thermostatting of up to 12 vials.
TurboMatrix HS 40 Trap 40 vials with intelligent, overlapped thermostatting of up to 12 vials plus built-in trap for lower detection limits.
TurboMatrix HS 110 Trap 110 vials with intelligent, overlapped thermostatting of up to 12 vials plus built-in trap for lower detection limits.
Hardware
Sample vials
Use PerkinElmer 22-mL sample vials (Part Number B0104236) for a maximum liquid sample volume of 15 mL. With the low-volume vial adapters (Part Number N6120110), the TurboMatrix HS 16 and TurboMatrix HS 40 models can also use 6-mL sample vials (Part Number N9302134) for a maximum sample volume of 2 mL. The 6-mL sample vials cannot be used on the TurboMatrix HS 110 models.
Note: Use of non-PerkinElmer sample vials and patented cap enclosures is NOT recommended and system performance problems resulting from the use of non-PerkinElmer vials and caps will NOT be covered under the system warranty.
Sample thermostatting
Solid aluminum thermostatting oven (available on TurboMatrix HS 40 and HS 110
thermostatting models only). Thermostatting period and temperature precisely controlled for each sample. Software algorithm automatically optimizes sample thermostatting overlap.
Sample temperature
Temperature settable from 35 ˚C to 210 ˚C in 1 ˚C increments or can be run at ambient.
Sampling needle
Stainless steel, platinum/iridium (optional), Siltek T- (standard on trap models).
Transfer line length
Choice of 1008 mm (standard) or 1650 mm.
Transfer line temperature
Transfer line system
Deactivated fused-silica capillary transfer line or capillary column (0.32-µm i.d. or 0.25-µm i.d.) shielded inside a heated transfer tube between the headspace sampler and GC injector.
Column compatibility
Compatible with all capillary-column diameters in split and splitless (direct coupled) mode. Oncolumn sampling using 0.25, 0.32 or 0.53-mm i.d. capillary columns and 1/8-inch o.d. packed columns.
Sampling method
Pneumatic, pressure-balanced sampling (no syringe or gas sample loop). Sample vials are
pressurized with carrier gas. During the injection period, carrier gas flowing to the GC system is replaced by pressurized sample gas. Rapid transfer of analytes is ensured without re-equilibration in a gas-sampling valve or syringe and subsequent loss of analytes. Injection amount is programmable by time or by volume without requiring any hardware change.
For headspace-trap sampling, the gas is focused on a sorbent trap before injection into the GC. This can be done for up to four cycles.
Analyte compatibility
Polar and non-polar organic compounds can be analyzed without any change of internal tubing. Low risk of sample-composition change during analyte transfer. Analysis of chemically-active compounds such as free volatile organic acids, sulfur compounds, amines and other nitrogen-containing organic compounds can be performed using the optional platinum/iridium or Siltek needle.
Pneumatic control
Choice of:
Manual pneumatics using built-in pressure regulator (0-60 psig), non-trap models only.
Electronically-controlled Programmable Pneumatic Control (PPC) module (0-60 psig).
Modes of operation
Constant mode
Routine analysis mode with constant, equal thermostatting time for each sample. Includes
intelligent, overlapped thermostatting to automatically optimize oven movement for maximized sample throughput.
MHE mode
Multiple headspace extractions from each vial. Up to nine extraction steps with intermediate
vent performed automatically. For use in method development and validation or for routine analysis of special samples.
Progressive mode
Method-development tool used in determining required equilibration time and in performing
kinetic studies. Thermostatting time is automatically increased to determine optimal thermostatting time.
Control
Standalone operation
Each headspace sampler is a self-contained standalone unit. All instrument functions are easily controlled from the touch screen of the built-in graphical user interface (GUI). Set and actual values may be displayed at any time. Configurable user interface for simplest possible interaction.
Simple one-touch operation
Single-method operation
Sequence-based multimethod operation of up to eight methods
Password protection
Ten operating methods can be stored in the instrument
Parameters remain stored with last-used method directly available after power-up
Operating languages
English, French, German, Italian, Japanese, Chinese, Spanish and Russian (GUI).
Software control
A Remote Control Software (RCS) package is available to control the headspace samplers from a Microsoft® Windows environment.
Complete, integrated control from TotalChrom® software.
Gas chromatograph/ data system interfacing
Output signal lines for READY and RUN to start gas chromatograph (GC) and data-handling devices. Input lines for START, STOP and READY to control the headspace unit externally.
Six built-in relays (4 with contact closures, 2 with 24-volt outputs).
Economy mode
Programmable power-saving and gas-saving feature with automatic wake-up function.
Priority vial
One or two-vial positions can be assigned to priority vials. Urgent vials can be placed in these positions and will be inserted into the analysis sequence for quickest possible analysis. Available for the TurboMatrix HS 40 and TurboMatrix HS 110, non-trap and trap models.
Maintenance alarms
Settable injection counter with a customizable display alerts users to perform routine maintenance.
System integrity checks
Automatic system leak checking
Static leak checks: Checks the whole system for leaks prior to analysis
Automatic vial leak checking
Dynamic leak check: Checks each vial for leaks as it is sampled (PPC systems only)
Optional accessories
Shaker
Patented, intelligent frequency shaker for quicker sample-specific equilibration during ther‑
mostatting. All vials are agitated simultaneously to allow quicker equilibration. Automatic frequency-checking program optimizes the agitation process. Available for the TurboMatrix HS 40 and TurboMatrix HS 110, non-trap and trap models.
Cryofocusing/water trap
On-column cryofocusing accessory for preconcentration of analytes and improved detection
water trap limits. Water trap included to allow large-volume sampling from aqueous samples without ice blockage. Available for the TurboMatrix HS 40 and TurboMatrix HS 110, non-trap models only.
BCD output
Output of sample number to external device. Standard on TurboMatrix HS 110, non-trap and
trap models.
Injector adapter kits
Injector adapter kits are available for most contemporary GCs. Side-mount kit available for
PerkinElmer Clarus®, AutoSystemTM and AutoSystem XL GCs.
Removable sample tray
Extra sample trays for vials to be loaded into while instrument is running. Available for the TurboMatrix HS 40 and TurboMatrix HS 110, non-trap and trap models.
Clarus injector interface
Special hourglass-injector insert to connect the fused silica transfer line from the headspace sampler to the capillary column provides the performance advantages of a direct connection, while still maintaining the convenience of connecting to a split injector.
Physical details
Ambient operating Temperature range: 15 °C to 32 °C
conditions Humidity: 75% maximum RH without condensation
Power requirements 100/120/240 V; 50/60 Hz; 900 VA
TurboMatrix HS 16 TurboMatrix HS 40 TurboMatrix HS 110
( non-trap and trap) ( non-trap and trap)
Width 43 cm (17 in) 43 cm (17 in) 43 cm (17 in)
Depth 58 cm (23 in) 61 cm (24 in) 61 cm (24 in)
Height 61 cm (24 in) 61 cm (24 in) 61 cm (24 in)
Weight 32 kg (70 lb) 33 kg (73 lb) 35 kg (77 lb)
Onze Labexchange-team zullen u graag helpen:
Christian Schmid Laboratorium en analytiek, Laboratoriuminrichting, Life science
Hubert Sauter Spectroscopie, Chromatografie