Merck-Hitachi L-7200
Objektnummer | B00014451 |
---|---|
Seriennummer | 014451 |
Object Naam | Merck-Hitachi L-7200 |
Status | Archiv |
Status, leverings- en betalingsvoorwaarden
Apparatuurcontrole
De gebruikte apparatuur wordt voorafgaand aan levering gecontroleerd door Labexchange Service GmbH. U ontvangt volledig functionerende apparatuur.
Verzending
De vermelde verzendtijden zijn telkens de kortste voor een artikel. In bepaalde gevallen kunnen de daadwerkelijke verzendtijden daarvan afwijken. De uiteindelijke verzendtijden worden aangegeven in de opdrachtbevestiging.
In de regel bieden we combinatieleveringen aan. Levertijden zijn afhankelijk van het artikel met de langste levertijd. Deelleveringen zijn mogelijk tegen een toeslag.
Verzendmethoden
Koeriersdiensten, transportbedrijven, zelf afhalen, levering door Labexchange wagenpark
Informatie levering
De prijzen zijn exclusief verzendkosten. De genoemde verzendkosten zijn de te verwachten kosten. Afwijkingen zijn mogelijk. In het geval geen kosten voor verzending zijn gespecificeerd, vraag die dan afzonderlijk aan.
De opgegeven vracht- en verpakkingskosten hebben betrekking op de goedkoopste transportroute en zijn onder voorbehoud van onvoorziene kostenstijgingen. Door onvoorziene gebeurtenissen kunnen vrachttarieven en levertijden op elk moment veranderen en moeten ze worden aangepast aan de huidige situatie. Incoterm coderingen volgens Incoterms 2010: Bij afhalen EXW, CFR voor zendingen over zee, CPT per luchtfracht, andere zendingen DAP. Opmerking: We geven geen preferentieel certificaat/EUR1 af. Bij zelf afhalen/af fabriek (EXW) uit derde landen en de EU wordt 16% btw als borg ingehouden, tot we de ontvangstbevestiging/het leveringscertificaat van de koper hebben ontvangen.
Betalingsvoorwaarden
Wij accepteren geen betalingen Letter of Credit, PayPal etc. Het factuurbedrag is volledig verschuldigd. Er zijn geen betalingskortingen. De goederen blijven tot volledige betaling ons eigendom.
Land |
Mogelijke betaalmethoden |
Opmerking |
Duitsland, Oostenrijk, Zwitserland |
Betaling via factuur, vooruitbetaling, per creditkaart |
Betaling via factuur is mogelijk voor ondernemingsklanten. |
Nederland, België en Luxemburg |
Betaling via factuur, vooruitbetaling, per creditkaart |
Betaling via factuur is mogelijk voor ondernemingsklanten. |
Andere landen |
vooruitbetaling, per creditkaart |
|
Onze Algemene Voorwaarden voor Verkoop, Levering en Betaling zijn hierop van toepassing. Deze voorwaarden zijn hier te downloaden.
Tussenverkoop is ons voorbehouden.
Beschrijving status:
Alle artikelen zijn gebruikte artikelen, tenzij bij een artikel uitdrukkelijk wordt vermeld dat het om een nieuw apparaat gaat.
Application
This instrument is used in combination with a liquid chromatography system to perform automatic analyses.
Configuration
The configuration of the L-7200 Autosampler is shown in Figure 3-1.
Samples to be analyzed are stored in a rack which is placed in a chamber that includes a syringe to allow aspiration of the samples can be moved along the transverse axis (X), the longitudinal axis (Y), and the vertical axis (Z). The injection valve is used to inject samples into the mobile phase flow. Syringes with a delivery volume of 0.1 and 0.5mL are available.
Analytical conditions are set via the keys on the keypad. The display panel presents information about the operational status of the system.
Flow path
Figure 1-3 includes the various components of the system that are
in contact with the sample and the wash solution in the L-7200
Autosampler. The needle can be moved along the X, Y and Z
axes to permit free movement between sample vials, the wash
port and the injection port. The action of the syringe is used to
withdraw sample from the sample vial and to deliver lt to the
injection port.
A cycle includes the following steps:
* The needle is cleaned in the wash port
* A sample solution is aspirated by the needle
* The sample solution is Ioaded into the loop of the injection valve
* The valve is switched to inject the sample into the mobile phase
Sample Injection Methods
The L-7200 permits three injection methods. In the standard injection method, the amount of sample that is withdrawn by the needle is slightly larger than the amount of sample that will be transferred from the injection valve to the column. The middle part of the sample is injected; the leading and trailing ends of the sample are not injected. This method is commonly called the cut injection method.
If the amount of a sample is small, the entire sample that is withdrawn via the needle is transferred into the sample loop and into the column. This method is called the all volume injection method.
In the full loop injection method, sample loop is filled with sample for measurement.
Cut lnjection Method
This method provides good reproducibility, however some of the sample is wasted.
Specifications
(1) Number of standard samples: 80
The vial number setting range is from 1 to 200
(2) Rack/sample vials:
Conditions can be set to accommodate a variety of sample vials and racks
(3) Syringe capacity:
0.5 mL (standard syringe)
(4) Sample injection volume:
0.5 pL to 400 pL (standard loop: 100 pL)
(5) Syringe speed:
5 speeds can be chosen by the analyst
(6) Sample injection method:
Syringe measurement cut injection
Synnge measurement all volume injection
Full loop measurement injection
(7) Pressure resistance: 34 MPa (350 kgf/cm 2 )
(8) Composition of components that are in contact with liquid:
Stainless steel (SUS316), tetrafluoroethylene (Teflon), borosilicated glass, Vespel, PEEK (polyethy lether ketone)
(9) Display:
LCD with back light (40 characters x 2 lines)
(10) Control system:
Sequential injection function for LC
(11) Vial detecting function:
Provided
(12) Data storage:
Battery backed-up memory
(13) Number of injections per sample:
Up to 99 times
(14) Analysis time:
999.9 minutes
(15) Extemal communication function:
D-Line communication
(16) GLP function:
Error detection: Abnormality in operation of the system is detectable.
Maintenance logbook: After part replacement, the number of injections is recorded. The count can be reset to zero after certain parts (e.g. injection port seal) have been replaced.
(17) Ambient temperature:
4 to 35°C
(18) Ambient humidity:
45 to 85%
(19) Power requirement:
100- 240 V AC ± 10%, 50/60 Hz
(20) Power consumption:
Approx. 85 VA
(21) Dimensions:
260(W) x 500(D) x 235(H) mm (excluding protrusions)
(22) Weight:
Approx. 19 kg