Dade DAC II
Objektnummer | B00013292 |
---|---|
Seriennummer | 013292 |
Object Naam | Dade DAC II |
Status | Archiv |
Status, leverings- en betalingsvoorwaarden
Apparatuurcontrole
De gebruikte apparatuur wordt voorafgaand aan levering gecontroleerd door Labexchange Service GmbH. U ontvangt volledig functionerende apparatuur.
Verzending
De vermelde verzendtijden zijn telkens de kortste voor een artikel. In bepaalde gevallen kunnen de daadwerkelijke verzendtijden daarvan afwijken. De uiteindelijke verzendtijden worden aangegeven in de opdrachtbevestiging.
In de regel bieden we combinatieleveringen aan. Levertijden zijn afhankelijk van het artikel met de langste levertijd. Deelleveringen zijn mogelijk tegen een toeslag.
Verzendmethoden
Koeriersdiensten, transportbedrijven, zelf afhalen, levering door Labexchange wagenpark
Informatie levering
De prijzen zijn exclusief verzendkosten. De genoemde verzendkosten zijn de te verwachten kosten. Afwijkingen zijn mogelijk. In het geval geen kosten voor verzending zijn gespecificeerd, vraag die dan afzonderlijk aan.
De opgegeven vracht- en verpakkingskosten hebben betrekking op de goedkoopste transportroute en zijn onder voorbehoud van onvoorziene kostenstijgingen. Door onvoorziene gebeurtenissen kunnen vrachttarieven en levertijden op elk moment veranderen en moeten ze worden aangepast aan de huidige situatie. Incoterm coderingen volgens Incoterms 2010: Bij afhalen EXW, CFR voor zendingen over zee, CPT per luchtfracht, andere zendingen DAP. Opmerking: We geven geen preferentieel certificaat/EUR1 af. Bij zelf afhalen/af fabriek (EXW) uit derde landen en de EU wordt 16% btw als borg ingehouden, tot we de ontvangstbevestiging/het leveringscertificaat van de koper hebben ontvangen.
Betalingsvoorwaarden
Wij accepteren geen betalingen Letter of Credit, PayPal etc. Het factuurbedrag is volledig verschuldigd. Er zijn geen betalingskortingen. De goederen blijven tot volledige betaling ons eigendom.
Land |
Mogelijke betaalmethoden |
Opmerking |
Duitsland, Oostenrijk, Zwitserland |
Betaling via factuur, vooruitbetaling, per creditkaart |
Betaling via factuur is mogelijk voor ondernemingsklanten. |
Nederland, België en Luxemburg |
Betaling via factuur, vooruitbetaling, per creditkaart |
Betaling via factuur is mogelijk voor ondernemingsklanten. |
Andere landen |
vooruitbetaling, per creditkaart |
|
Onze Algemene Voorwaarden voor Verkoop, Levering en Betaling zijn hierop van toepassing. Deze voorwaarden zijn hier te downloaden.
Tussenverkoop is ons voorbehouden.
Beschrijving status:
Alle artikelen zijn gebruikte artikelen, tenzij bij een artikel uitdrukkelijk wordt vermeld dat het om een nieuw apparaat gaat.
The following illustrations and descriptions are referring to the instrument model and are drawn from brochures. They are not representing the delivery volume. The exact delivery content you will find only in the offering text.
1-1: Dade Automatic Centrifuge II
Functional Description
The Dade® Automatic Centrifuge II is a laboratory bench-top, multi-purpose, electromechanical instrument designed to perform cell washing and immunohematology procedures including cell resuspension. lt provides the laboratory with a fast wash cycle capability, thereby lowering laboratory time costs. lt can be easily programmed to automatically perform one, two, three, four or five wash cycles per test sequence. Each cycle consists of programmed saline introduction and subsequent decanting during centrifugal rotation. The System provides a saline monitoring feature to warn the Operator when saline is not being delivered. The centrifuge incorporates variable spin times for several different types of centrifuge operation. Decant RPM is Operator adjustable to give more than 0.1 mL residuals if desired.
An agitation cycle resuspends cells for approximately 5 seconds and then spins the cells for 20 seconds before completion of the cycle. The agitate time, as well as spin after agitate time, is operator-programmable. The front control panel (See Figure 1-2) contains a vacuum fluorescent display of RPM functions and time which allows the operator to continually monitor the status of instrument operation.
Physical Description
The centrifuge is a self-contained Instrument 14.5 inches (36.8 cm) high, by 12.75 inches (32.4 cm) wide, by 16 inches (40.7 cm) deep, and weighs approximately 43 pounds (20 kg). lt is mounted on a heavy metal base with two adjustable front feet and two stationary rear feet. A power cord with a threepronged plug provides primary power to the unit.
The microprocessor-controlled electronics portion of the instrument consists of the Control and Display Printed Circuit (PC) Board. This PC Board coordinates the Operation of the instrument control panel and keyboard, electronic detectors, and control elements throughout the instrument. The board also visually displays the motor RPM, wash count or function and time through the three display view windows located on the front control panel. An "end of cycle" is signaled by an audible signal.
The four basic assemblies or components that comprise the mechanical portion of the instrument (see Figure 1-3) are as follows:
A. Centrifuge inner bowl - The centrifuge inner bowl houses the centrifuge rotor with 12-tube carrier. Access to these components is gained by opening the centrifuge top cover. The inner bowl is easily removed for cleaning. Warning: After replacing the removable bowl, and before installing the rotor, rotate the rotor drive by hand until it turns freely. The saline dispensing adapter, located on the top and inside of the centrifuge cover, is connected to the saline pump by the saline output tubing (see Figure 1-3). The saline drain outlet is located at the rear of the centrifuge bowl and extends out of the rear of the instrument. An overflow drain is located just above the normal drain fitting.
B. Centrifuge rotor - The centrifuge rotor has a capacity of 12 test tubes of either 10 x 75 mm or 12 x 75 mm size. All loadbearing components are manufactured from high grade, corrosion-resistant stainless steel. The rotor may be removed from the instrument by grasping the upper collar of the rotor and lifting. The centrifuge rotor can be placed either on a bench top or in a water bath, as the bottoms of the tube carriers act as supports.
C. Test tubes - Either 10 x 75 mm or 12 x 75 mm glass test tubes can be used in the rotor. Use of a 10 mm adapter (P/N S23265-001) in each tube carrier is required for 10 x 75 mm test tubes.
D. Control panel - The control panel (also referred to as the operator's panel or front panel) is equipped with a vacuum fluorescent alphanumeric readout display of RPM functions and time which allows the Operator to continually monitor the status of instrument Operation. All panel switches are the tactile type, activated by applying finger pressure to the embossed panel surface. A "rocker" power switch is mounted through the front panel.
1-3: Dade Automatic Centrifuge II Wash Enclosure, Bowl and Rotor
Performance Characteristics
The Dade® Automatic Centrifuge II encompasses the following performance characteristics:
The instrument can be programmed to perform one, two,
three, four, or five wash cycles per test sequence.
Spin function can be selected for a preset spin time of 20
seconds.
Manual Operation of the instrument allows for variable spin
times up to a maximum of 9 minutes 59 seconds.
An agitation function is provided for resuspension, then
centrifugation of the resuspended mix.
Front panel keys are tactile type.
RPM, Function and Time readout displays permit constant monitoring of instrument Operation.
An audible signal accompanies the end of all test programs.
The centrifuge Iid interlock prevents instrument Operation if the centrifuge cover is open.
Decant RPM is operator-adjustable for a dry (790 RPM) or wet (750 RPM) cell button.
The centrifuge lid lock prevents operator from opening cover during instrument operation.
The instrument is automatically grounded when connected to properly grounded power source.
Saline volume is microprocessor-controlled.
All programmed functions last selected and entered via the ENT key will be retained even after power is turned off.
Specifications
The specifications listed below are subject to change without notice to allow the introduction of design improvements.
Automatic controls
Rotating
Radius
Speed approx. Time
Auto * Wash 0-3200 RPM N/A 4 sec.
Wash * Fill 3000-3200 RPM 9.2 cm (925-1050 rcf) 16 sec.
Sequence * Pack 3000-3200 RPM 9.2 cm (925-1050 rcf) 14 sec.
* Pause 3200-0 RPM N/A 10 sec.
* Decant 750-790 RPM 4.8 cm (19-34 rcf) 9 sec.
Auto * Spin 3000-3200 RPM 9.2 cm (925-1050 rcf)
Spin
Auto * Agitate N/A (5 second agitation
Agitate & 20 second spin) 25 sec.
Manual Controls
Rotating
Radius
Speed approx. Time
* Spin 3000-3200 RPM 925-1050 rcf Programmable
(1 second - 9 minutes
59 seconds)
* Agitate N/A - Programmable
(1-9 seconds)
* Spin after 3000-3200 RPM - Programmable
agitate (1 second-2 minutes
55 seconds)
Electrical
Catalog No. B5054-2X
* Volts 220-240 VAC
* Amperage (max.) 1.5A
* Cycles 50 Hz
Physical
* Height 14.5 in. (36.8 cm)
* Width 12.75 in. (32.4 cm)
* Depth 16.0 in. (40.7 cm)
* Weight 43.0 Ibs. (20.0 kg) approx.
* Shipping weight 58 Ibs. (26.3 kg) approx.