Shimadzu CR 4A
Objektnummer | B00013545 |
---|---|
Seriennummer | 013545 |
Nome oggetto | Shimadzu CR 4A |
Stato | Archiv |
Status, terms of delivery and payment
Verification of devices
The second-hand devices are verified by Labexchange Service GmbH before delivery. You are receiving only fully functional devices.
Dispatch time
The stated dispatch times are the shortest possible ones for each article. The effective dispatch times can vary. The effective dispatch times will be stated in the order confirmation.
As a matter of principle, we are offering collective deliveries. The shipping time is calculated based on the position with the longest lead time. A partial delivery is possible on explicit request.
Shipping methods
Parcel services, forwarding agencies, self-pickup, delivery by Labexchange fleet.
Delivery information
Prices exclude shipping costs. Stated shipping costs are to be expected. Deviations are possible. If transport costs are not specified, please ask separately for them.
For deliveries to countries outside the EU, an additional fee of 70,00€ for export is charged. Note for international shipments: A proof of preference/EUR1 will not be issued by us. When self-collecting/ordering EXW from countries within or outside the European Union, 16% VAT will be retained as a deposit until we have received the corresponding confirmation of arrival/bill of delivery from the buyer.
Terms of payment
We do not accept payment by credit card, letter of credit, PayPal, etc. In each case the invoice amount is payable without deduction. Discount is not granted.
Country |
Possible payment methods |
Comment |
DE, AT, CH |
Payment by invoice, payment in advance |
Payment by invoice is only possible for corporate clients. |
NL, BE, LU |
Payment by invoice, payment in advance |
Payment by invoice is only possible for corporate clients |
Other countries |
Payment in advance |
|
Our General Terms of Sale, Delivery and Payment are valid and are available for download here.
The goods are offered subject to prior sale.
Definition of status
All articles are used articles, except an article is listed especially as a new device.
Status |
Condition |
Comment |
Immediately available |
Used | The article is fully functional and in impeccable condition. It can be shipped immediately. |
In stock |
Used |
The article is on stock. Our service technicians will verify the article before delivery. You are receiving only a fully functional article. |
Published |
Used |
The article is still with the provider. After your order the article will be purchased and verified by us before being shipped to you. A certificate of operativeness as well as a service report are included in delivery. |
New device |
new |
The article is brand new and unused. Regarding new equipment the guarantee/warranty conditions of the corresponding manufacturer apply. |
Firma: Shimadzu
Kommentar: Dokumente für IDNR. 12275
The following illustrations and descriptions are referring to the instrument model and are drawn from brochures. They are not representating the delivery volume. The exact delivery content you will find only in the offering text.
RID-6A
Specifications
Measuring System: Deflection type
Range of refractive index: 1 to 1.75
Measuring range: 0.25 X 10 -4 to 512 X 10 -6 RIU FS, selectable in 12 steps
Noise level: 2.5 X 10 -9 RIU short term noise for water-sealed and SLOW response conditions; short term noise as defined by ASTM
Linearity: 8 X 10 -4 RIU or higher
Cell volume: 10µl
Material in contact with liquid: SUS316, quartz, Teflon
Response: 3 step selection: FAST, STD and SLOW
Controlled temperature of cell: 35°C (Thermal fuse 70°C)
Zero adjustment: Optical zero adjustment
Automatic zero adjustment
Fine zero adjustment (manual)
Auto zero adjustment range: Maximum of ±4 X 10 -4 RIU
Auto zero adjustment accuracy: Maximum of ±3 X 10 -8 RIU
Recorder: 1mV, 10mV full scale
Integrator terminal output: 0.4V/1 X 10 -4 RIU, 0.1V/1 X 10 -4 RIU
Weight: 13kg
Size: 26(W) X 16(H) X 40(D) cm
Optimum operating temperature range: 10 to 40°C (when temperature is not controlled) Power requirements: RID-6A is classified as follows according to the supply voltage:
P/N 228-16510-91 100V±10V 1A 50, 60Hz
228-16510-92 115V±10V 1A 50, 60Hz
228-16510-93 220V±20V 0.5A 50, 60Hz
228-16510-94 240V±20V 0.5A 50, 60Hz
228-16510-95 230V±20V 0.5A 50, 60Hz
DGU-3A
Outline of Degasser
The DGU-3A online degasser continuously removes gases dissolved in liquid through a special plastic membrane.
When the degasser is connected to the HPLC pump, the degasser continuously removes gases dissolved in the mobile phase without changing its composition. Consequently, the degasser improves stability and repeatability in HPLC analysis because it prevents generation of bubbles due to dissolved gases, poor delivering of the pump due to bubbles, noise an the baseline of the detector, and fluctuation of the detector baseline due to the variation of dissolved gas concentration.
The DGU-3A has three independent flow paths and the DGU-4A has two independent flow paths. The degassing characteristic per flow path and other functions are common to both the DGU-3A and DGU- 4A, and the only difference between them is the number of flow paths.
The operating principle of the degasser is illustrated below.
The mobile phase passes through the special plastic membrane mounted in the vacuum chamber of the degasser. Gases dissolved in the liquid selectively pass through the membrane into the space in the vessel because of smaller gas molecular sizes, and higher mobility than the liquid, and the close affinity of gases to the membrane. In the above process, gases are removed from the liquid to the space in the vacuum chamber and are then exhausted out of the system.
Specifications:
Degassing characteristics The concentration of residual dissolved oxygen at the outlet of the degasser is 1.5ppm max. per flow path when air-saturated ion-exchanged water at an ambient temperature of 25°C is passed through the degasser at a flow rate of 3ml/min max.
Maximum flow rate 10ml/min (water)
Internal volume About 15ml per flow path
Operating pressure 2kg/cm 2 max. (Use is limited to the suction side, i.e., inlet, of the pump. Feeding of liquid to the degasser under pressure is not allowed.)
Connecting tubes Teflon tubes of 3mm OD and 2mm ID
Wetted materials Special plastic resistant to all solvents (degassing membrane), Kel-F (connection joints), Teflon (connection tubes)
Other
Self-cleaning When the vacuum pump is started or stopped, the solenoid valve is switched over to draw in ambient air to prolong the service life of the vacuum pump.
Safety feature A device is provided to stop the vacuum pump automatically if the vacuum pump is over-heated.
(Remains in standby to allow natured cooling.)
Dimensions Width 260mm, height 140mm, depth 400mm
(Not including projecting parts)
Weight 13kg
Ambient temperature and humidity: 10 to 40°C and 40 to 85%, respectively
Storage temperature 0 to 60°C (with the flow paths dried)
Power supply: DGU-3A is available in the following modifications according to the power supply voltage.
P/N 228-24200-91 AC100V±10% 100VA 50/60Hz
P/N 228-24200-92 AC115V±10% 100VA 50/60Hz
P/N 228-24200-93 AC220V±10% 100VA 50/60Hz
P/N 228-24200-94 AC240V±10% 100VA 50/60Hz
P/N 228-24200-95 AC230V±10% 100VA 50/60Hz
Detector SPD-6AV
Specifications
Wavelength range 195 to 700nm
Wavelength accuracy ±2nm
Wavelength reproducibility ±0.5nm
Spectral bandwidth 8nm
Light source Deuterium (D 2 ) lamp (195370nm)
Tungsten halogen (WI) lamp (370700nm)
Diffraction Grating Blazed holographic type with 1200 grooves/mm
Cell volume (STD) 8µl (lmmØ X 10mm)
Cell pressure tolerance 30kg/cm 2
Materials in contact with liquid SUS 316, quartz, Teflon
Base line noise 3 X 10 -5 AU Max. at 250nm, 500nm
(using air in the cell, as a response STD)
Base line drift 1 X 10 -3 AU/hour Max. 250nm, 500nm
(using air in the sample cell)
Measurement range 0.001, 0.002, 0.005, 0.01, 0.02, 0.04, 0.08, 0.16, 0.32, 0.64, 1.28, 2.56, AUFS - intervals of selectable in 12-steps
Response 3-step selection: FAST, STD and SLOW
Corresponding to 0.05, 0.5 and 1.5 sec time constants. However, an internal switch can change the time constants to 0.1, 1.0 or 3 sec.
Zero adjustment Auto zero by pushbutton switch
Zero adjustment range Maximum of 1.4AU
Zero adjustment accuracy Maximum of ± 1 X 10 -4 AU
Recorder terminal outputs 1mV, 10mV full scale
Integrator terminal output 0.4V/AU, 0.8V/AU
Weight 14kg
Size 26(W) X 16(H) X 40(D) cm
Optimum operating temperature range 10° to 40°C
Power requirements (SPD-6AV is classified as follows according to supply voltage.)
P/N 228-15001-91 100V ± 10V 1.3A 50, 60Hz
P/N 228-15001-92 115V ± 10V 1.3A 50, 60Hz
P/N 228-15001-93 220V ± 20V 0.7A 50, 60Hz
P/N 228-15001-94 240V ± 20V 0.7A 50, 60Hz
P/N 228-15001-95 230V ± 20V 0.7A 50, 60Hz