Wave Biotech AG Thermasept II
Objektnummer | B00021950 |
---|---|
Numéro d'identification | 021950 |
Nom de l'objet | Wave Biotech AG Thermasept II |
Statut | Archiv |
Statut, conditions de livraison et de paiement
Vérification des appareils
Les appareils d’occasion sont vérifiés par Labexchange Service GmbH avant la livraison. Vous recevez des appareils entièrement fonctionnels.
Délai d'expédition
Les délais de livraison indiqués sont les plus rapides pour l’article en cause. Les délais de fait peuvent varier au cas par cas. Les délais de livraison définitifs sont indiqués dans la confirmation de commande.
Nous offrons des livraisons collectives par principe. Le délai de livraison s’oriente à l’article avec le délai de livraison le plus long. Une livraison partielle est possible par prix additionnel.
Méthodes d'expédition
Courrier, agences d'expédition, autocueillette, livraison par flotte de Labexchange
Conditions de livraison
Prix plus frais d’expédition. Les frais d’expédition indiqués sont à prévoir. Dérogations éventuelles sont possibles.
Si les coûts de transport ne sont pas spécifiés, s'il vous plaît demander séparément les frais de transport. Les frais de transport et d'emballage indiqués se réfèrent à l'itinéraire de transport le moins cher et sont sujets à des augmentations de coûts imprévues. En raison d'événements imprévisibles, les tarifs de transport et les délais de livraison peuvent changer à tout moment et doivent être adaptés à la situation actuelle. Incoterm codage selon les Incoterms 2010: Pour personnes qui viennent chercher les dispositifs elles-mêmes: EXW, pour les expéditions par voie maritime: CFR, par avion: CPT, d'autres expéditions: DAP. Remarque: Nous n'établissons pas des preuves préférentielles/EUR1. Dans le cas d’un enlèvement par vos soins/EXW de pays à l’intérieur ou à l’extérieur de la Union européenne, nous devons conserver 16% de TVA d’acheteur comme dépôt de garantie, jusqu’à ce que nous ayons reçu l’attestation de reception/la prevue de livraison.
Modalités de paiement
Nous n’acceptons pas le paiement par lettre de credit, PayPal, etc. Dans tous les cas le montant est payable sans déduction. Jusqu’au paiement complèt l’équipement reste notre propriété. Un escompte n’est pas accordé.
Pays |
Modalités de paiement possible |
Remarque |
DE, AT, CH |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
NL, BE, LU |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
Autre pays |
Prépaiement, par carte de credit |
|
Nos conditions de vente, de livraison et de paiement sont en vigueur. Vous pouvez télécharger les documents ici.
La vente intermédiaire nous est réservée.
Défintion des statuts
Tous articles sont d’occasion, sauf si explicitement défini comme « appareil neuf ».
Statut |
Condition |
Remarque |
Immédiatement disponible |
Occasion |
L’article a été déjà entièrement vérifié et peut être envoyé directement à vous. |
En stock |
Occasion |
L'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels. |
Publié |
Occasion |
L’article est toujours au l’offreur. Nous achetons, vérifions et en fin livrons l’article après votre commande. Le certificat de fonctionnement ainsi que le rapport de service sont inclus à la livraison. |
Appareil neuf |
Neuf |
C’est un dispositif neuf. L’article n’est pas utilisé et neuf d’usine. En ce qui concerne des article neufs, la garantie du fabricant est valable. |
Labprocure |
Occasion |
Responsable du contenu de l‘offre d’appareil est la société Labprocure GmbH, comme annonceur. Labprocure assume la responsabilité des offres annoncées ici ainsi que des photos et des textes d’offre inclus. Labprocure GmbH, Bruckstraße 58, 72393 Burladingen. |
model: Thermasept II
annotation: Dokumente engl.
The following illustrations and descriptions refer to the instrument model and are drawn from brochures. They do not represent the scope of delivery. Please refer to the text of the offer for the exact scope of delivery.
Technical information
The BioWave 200SPS-F contains all features for production. There is only one execution available.
BioWave 200SPS-F
Operation
Fully automated, PLC controlled system, operation by front coloured LCD touch screen display with back-lightning. The display can be rotated. Fully menu-guided operation. With integrated features:
Password:
Viewer, User and Supervisor mode.
Alarm:
Exceeds the actual values, the pre-defined upper and lower alarm values and alarm message will be shown on the display. Alarm outputs can be connected at any customer devices to act respectively.
Controller:
pH can be controlled by connected peristaltic pumps (add base and acid) or CO 2 content in air flow. DO can be controlled by 0 2 content in the air flow.
Stopwatch:
For easier writing of protocols.
Time:
Integrated, battery powered date for data acquisition.
Acceleration mode:
Increasing/decreasing rock rate during pre-adjusted time.
Working hours:
Counting total working hours of BioWave.
Set flow:
Adjustable at display. CO 2 and 0 2 content are predefined in %. Flexible hoses with couplings to connect bags are included with BioWave 200 SPS-F.
Quick mounting of Wave Bags
Two large handles at the front rear side allow to fix the Wave Bags immediately and securely without damaging the Wave Bag.
Aeration control
Sucks either ambient air for aeration through a connector at the rear side panel or receives pressurised air connected at the pressurised air port. A positive pressure applied at the pressurised air port stops automatically the air pump.
Gases to connect
· Ambient air: Centrifugal air pump built-in, max. pressure 500 mbar.
· Pressurised air port: Built-in pressure reducer, Input pressure +0.8...+1.0 bar, to connect by user. Safety pressure measurement avoiding to high over pressure in the Wave Bag.
· CO 2 , +0.8...+0.8 bar
· O 2 , +0.8...+0.8 bar
Air flow rate
· Using ambient air: 0...4.0 l/min, +/- 0.2 l/min.
· Using pressurised air: 0...4.0 I/min, +/- 0.2 l/min.
CO 2 content in the air flow
1.0...12 % +/- 0.5 %
O 2 content in the Air Flow
21... 50 % +/- 1.0 %
Measurement CO 2 and O 2
Content of CO 2 and O 2 in air flow are measured by IR sensor.
Over pressure protection
Pressure transmitter measuring constantly the positive pressure. Switches off
the air flow in case of too high pressure to avoid too high pressure in the Wave Bag.
No Flow Alarm
An alarm will be shown on the display in case of no air flow is dedected.
DO and pH measurement
The two light fibre cables from the pH/DO inserted into the respective ports of
the Wave Bags D opt. are measuring the light luminescence decay time response from the sensor caps. The light fibre cables are marked with colours to avoid insert into the wrong port of the Wave Bag. The DO and pH of only one Wave Bag D opt. can be measured at the same time. For principle of measurement see data sheet Wave Bag D opt.
Parameters measured
DO content of media: 0...200 % +/- 2% (yellow)
pH of media 5.5... 9.0, +/- 0.2 (red)
Calibration
The Wave Bag D opt. is marked with individually calibration codes. This codes have to be entered at the display. There is no periodically calibration required.
Temperature influence of media
The actual temperature of the media in the Wave Bag D opt. has to be entered by the operator to compensate the temperature shift.
Length of fibre cables
2.5 m.
Filter Heater
Heating of Wave Bags generates small amounts of vapour rising into the air outlet filter. The filter heater keeps the vent filter dry and prevents condensation from plugging the filter media. A green LED shows the heater is heating.
Temperature range
40...50°C, +/- 5°C
Material
Silicon
Heating power
2 Watt
Installation
The filter heater is put over the outlet filter manually without using any tools.
Power Supply
Built-in BioWave 200SPS, 6 VDC, 2m cable length
Number included
2
General data
Rocking Rate
3...20 rocks/min, +/- 1 rocks/min, adjustable at display.
Rocking Angle
4...10°, +/-0.3°, adjustable at display. Actual angle is shown on display.
Temperature Control
On PLC programmed PID controller. Heating of left side and/or right side for
heating of one 100L or two 100L or one 200L mounted Wave Bags at different temperatures. Selectable at front LCD display as the set temperature as well.
Temperature range
+20...+40 °C, +/- 0.2 °C.
Temperature measurement
Resistance thermometer 1x Pt100 class A (IEC751) built-in in button-housing for measurement of Wave Bag content. Two resistance thermometer are included measuring the temperature of two mounted Wave Bags
Serial interface
1x RS232/RS485, for either printer EPSON or software PCDAQ.
Material housing and Frame
Stainless steel 1.4301 (304), brushed, electro polished.
Safety
Emergency switch off, safety rubber bar installed at rocking table. They stop
rocking when touched. Key to lock the main power supply of the BioWave 200SPS.
Wheels
Stainless steel 1.4301 (304), polyurethane.
Transportation
Tilt position reducing required width for transportation WxDxH 1'930x890x1'200 mm.
Dimensions
WxDxH 1'930x1100x1100mm.
Weight
Complete system, without Wave Bags: 210kg.
Power supply
230 V -50 Hz, 10 A
Ingress protection
IP40 minimum
Ambient temperature range
0...+50°C Note: only for equipment and not for process application