Spéctromètres de masse

Waters LCT Premier

Prix Spécial 15 148,25 €
-35%
Remise
until 31 mai 2024
Prix normal 23 305,00 €
Excl. 19% VAT , excl. Shipping Cost
18 026,42 € incl. Vat
Numéro d'identification: 33615
Statut: En stockL'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels.?L'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels. Immediately available"
Envoi: 4-6 semaines
Description:
Waters Spectromètre de masse LCT Premier.
Avec source ESI. vaporisateur de verrouillage.
Boîtier de commande de pompe rotative.
Logiciel MassLynx Version 4.- + AddOns.
230 V. 50/60 Hz.
Installation
Nous réalisons l’installation de ce système de laboratoire professionnelle. Nous serons heureux de vous offrir l’installation de cet appareil de laboratoire pour 2840€, hors frais de voyage.

Dans la plupart des cas, les équipements de laboratoire et les systèmes d’analyse sont des appareils de très haut niveau technique, avec des spécifications et des exigences qui leur sont propres. Lors de la mise en service d’un appareil de laboratoire, bien souvent des questions se posent : comment monter et régler l’appareil, comment le mettre en route.


Nous serons heureux de prendre en charge de l’installation professionnelle de vos systèmes de laboratoire!

S’il vous plaît contactez-nous


Profitez de nombreux avanatges avec l’installation par nous:

  • Mise en service immédiate de votre système de laboratoire sans douceur
  • Une installation professionnelle prolonge la durée de service de votre système de laboratoire
  • La garantie est prolongée à 3 mois complets
  • Pas de frais de transport*
  • Vous avez droit à la garantie de rachat Labexchange

*sauf pour les produits des catégories équipement de laboratoire et flux laminaire. Dans certains cas individuels, exclusion aussi d’autres catégories de produits.


Demander une offre
Plus d’information
Objektnummer B00033615
Numéro d'identification 33615
Nom de l'objet Waters LCT Premier
Statut Lagergerät
Fabricant Waters
Envoi 4-6 semaines

Statut, conditions de livraison et de paiement

Vérification des appareils

Les appareils d’occasion sont vérifiés par Labexchange Service GmbH avant la livraison. Vous recevez des appareils entièrement fonctionnels.

 

Délai d'expédition

Les délais de livraison indiqués sont les plus rapides pour l’article en cause. Les délais de fait peuvent varier au cas par cas. Les délais de livraison définitifs sont indiqués dans la confirmation de commande.

Nous offrons des livraisons collectives par principe. Le délai de livraison s’oriente à l’article avec le délai de livraison le plus long. Une livraison partielle est possible par prix additionnel.

 

Méthodes d'expédition

Courrier, agences d'expédition, autocueillette, livraison par flotte de Labexchange

 

Conditions de livraison

Prix plus frais d’expédition. Les frais d’expédition indiqués sont à prévoir. Dérogations éventuelles sont possibles.

Si les coûts de transport ne sont pas spécifiés, s'il vous plaît demander séparément les frais de transport. En cas d’expédition dans des pays situés en dehors de l’union Européenne, des frais additionnels de 70,00€ pour l’exportation sont facturés. Remarque: Nous n'établissons pas des preuves préférentielles/EUR1. Dans le cas d’un enlèvement par vos soins/EXW de pays à l’intérieur ou à l’extérieur de la Union européenne, nous devons conserver 16% de TVA d’acheteur comme dépôt de garantie, jusqu’à ce que nous ayons reçu l’attestation de reception/la prevue de livraison.

 

Modalités de paiement

Nous n’acceptons pas le paiement par carte de credit, lettre de credit, PayPal, etc. Dans tous les cas le montant est payable sans déduction. Jusqu’au paiement complèt l’équipement reste notre propriété. Un escompte n’est pas accordé.

Pays

Modalités de paiement possible

Remarque

DE, AT, CH

Paiement par facture, prépaiement

Paiement par facture est possible pour clients professionnels.

NL, BE, LU

Paiement par facture, prépaiement

Paiement par facture est possible pour clients professionnels.

Autre pays

Prépaiement

 

 

Nos conditions de vente, de livraison et de paiement sont en vigueur. Vous pouvez télécharger les documents ici.

La vente intermédiaire nous est réservée.

 

Défintion des statuts

Tous articles sont d’occasion, sauf si explicitement défini comme « appareil neuf ».

Statut

Condition

Remarque

Immédiatement disponible

Occasion

L’article a été déjà entièrement vérifié et peut être envoyé directement à vous.

En stock

Occasion

L'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels.

Publié

Occasion

L’article est toujours au l’offreur. Nous achetons, vérifions et en fin livrons l’article après votre commande. Le certificat de fonctionnement ainsi que le rapport de service sont inclus à la livraison.

Appareil neuf

Neuf

C’est un dispositif neuf. L’article n’est pas utilisé et neuf d’usine. En ce qui concerne des article neufs, la garantie du fabricant est valable.

manufacturer :      

model :                  

annotation :           Dokumente engl .

 

 

 

 

 

 

 

 

 

Overview of the LCT Premier

 

The LCT Premier TM time-of-flight (TOF) mass spectrometer features a ZSpray source with electrospray ionization (ESI) and modular LockSpray TM interface.

 

The LCT Premier uses ion guide technology for optimum transfer of ions from the source to the orthogonal acceleration time of flight ( oa -TOF) mass analyzer. Ion detection is by dual microchannel plate detector assembly. Data is acquired by a 4.0 GHz time-to-digital converter (TDC) and histogrammed in an embedded PC. Instrument control and data acquisition is by the MassLynx TM software system.

 

 

lonization Techniques

Using the Zspray atmospheric pressure ionization (API) source, three techniques are available.

 

ElectroSpray lonization

Atmospheric Pressure Chemical lonization

Atmospheric Pressure Photoionization

 

 

 

 

Performance Specifications

 

Resolution in Positive Ion (V Mode)

Infuse mellitin at a concentration of 5 pmol /µL, in 50:50 acetonitrile :water + 0.2% formic acid, using a flow rate of 5 µL/min. Ensure that the intensity of the peak at 712 Da is <300 counts/s.

The peak at 712 Da should be resolved such that the mass divided by the peak width at half height is greater than 5000 when using a scan time of 1 s and an inter-scan delay of 0.1 s. At least 30 s of data should be summed.

 

Resolution in Positive Ion (W Mode)

Infuse mellitin at a concentration of 5 pmol /µL in 50:50 acetonitrile :water + 0.2% formic acid, at a flow rate of 5 µL/min. Ensure that the intensity of the peak at 712 Da is <300 counts/s.

The peak at 712 Da should be resolved such that the mass divided by the peak width at half height is greater than 10,000 when using a scan time of 1 s and an inter-scan delay of 0.1 s. At least 30 s of data should be summed.

 

Resolution in Negative Ion (V Mode)

Infuse raffinose at a concentration of 500 pg/µL in 50:50 acetonitrile :water , at a flow rate of 10 µL/min. Ensure that the intensity of the peak at 503 Da is <300 counts/s.

The peak at 503 Da should be resolved such that the mass divided by the peak width at half height is greater than 5,000 when using a scan time of 1 s and an inter-scan delay of 0.1 s. At least 30 s of data should be summed.

 

Resolution in Negative Ion (W Mode)

Infuse raffinose at a concentration of 500 pg/µL in 50:50 acetonitrile :water at a flow rate of 10 µL/min. Ensure that the intensity of the peak at 503 Da is < 300 counts/s.

The peak at 503 Da should be resolved such that the mass divided by the peak width at half height is greater than 10,000 when using a scan time of 1 s and an inter-scan delay of 0.1 s. At least 30 s of data should be summed.

 

Sensitivity in Positive Ion

In V mode, infuse 50 pg/µL of leucine enkephalin in 50:50 acetonitrile :water + 0.1% formic acid at a flow rate of 5 µL/min. Using a scan rate of 1 s, an inter-scan delay of 0.1 s and a mass range of 100 to 1000 Da , check that the resolution at 556 Da is greater than 5000 and the intensity is greater than 440 counts/s.

Switch the instrument to W mode. Check that the resolution is greater than 10,000 and the intensity is greater than 110 counts/s .

 

Sensitivity in Negative Ion

In V mode, infuse 500 pg/µL. of raffinose in 50:50 acetonitrile :water at a flow rate of 10 µL/min. Using a scan rate of 1 s, an inter-scan delay of 0.05 s and a mass range of 100 to 1000 Da , check the resolution at 503 Da is greater than 5000 and the intensity is greater than 240 counts/s.

Switch the instrument to W mode. Check that the resolution is greater than 10,000 and the intensity is greater than 60 counts/s .

 

Mass Calibration Accuracy

Infuse 50 pg/µL of sodium formate at a flow rate of 5 µL/min into the analyte probe.In V mode, ensure that the intensity is less than 300 counts/s and that the resolution is greater

than 5000. Run a calibration using the parameters listed in Table E-1, with no smoothing and no background subtraction, and using a centroid top value of 80%.

 

Table E-1 Mass Calibration Accuracy Parameters

 

Scan Type                               Continuum

--------------------------------------------------------------

Scan Range                            150-900 Da

Scan Time                               5 s

Inter-Scan Delay                     0.1 s

Acquisition Time                      1 min

 

 

Save the calibration and then perform an acquisition for 1 minute using the same parameters. Combine and center the data, using 4 channels and a centroid top value of 80%.Measure at least 6 peaks and calculate the mass error ( ppm ) for each peak. Using the formula below, calculate the RMS error. The RMS error should be < 5 ppm .

 

Mass Measurement Accuracy

Infuse 50 pg/µL of sodium formate at 5 µL/min into the analyte probe . In W mode, ensure that the intensity is less than 300 counts/s and that the resolution is greater than 10,000. Run a calibration using the parameters listed in Table E-1. Create a calibration with no smoothing and no background subtraction, using a centroid top value of 80%.Save the calibration and then perform the following acquisition.

Infuse 50 pg/µL of leucine enkephalin into the reference probe and 500 pg/µL of raffinose into the ESI probe. Ensure that both probes give an intensity of <200 counts/s and that the resolution is greater than 10,000.

Acquire data in LockSpray mode for 25 minutes, using the following parameters:

 

Scan Type                               Continuum

--------------------------------------------------------------

Scan Range                            100-1000 Da

Scan Time                              1 s

Inter-Scan Delay                     0.1 s

Acquisition Time                      25 min

Reference Scan Frequency   5

Reference Cone Voltage        100 V

 

Combine 12 scans at each of the following times: 2, 4, 6, 8, 10, 12, 14, 16, 18, 20 minutes.

Using the Mass Measure feature an each of the spectrums, create a centered spectrum using lockmass 556.2771 Da . Calculate the RMS error using the formula below. The m/z value of raffinose is 527.1588 Da .

The calculated RMS error should be <3 ppm .

 

Chromatographic Signal to Noise

Note: This test should only be performed if there is already a suitable HPLC system installed.

Infuse 50 pg/µL of leucine enkephalin at a flow rate of 5 µL/min. Tune the ion beam in V mode and check that the resolution is greater than 5000.

Purge the HPLC using 75:25 methanol :water and 5 mM ammonium acetate. Connect the 10-µ.L sample loop, injection port, and waste tube to the Rheodyne injector. Connect a Waters Atlantis dC18 column (2.1 x 30 mm; 3 µM) between the injector and the probe. Condition the column for approximately 20 minutes.

Set up the following sample list acquisition parameters:

 

Table E-2 Sample List Acquisition Parameters

 

Scan Type                               Continuum

---------------------------------------------------------------

Scan Range                            150-900 Da

Scan Time                               2 s

Enter-Scan Delay                    0.I s

Acquisition Time                      30 min

 

Make five injections of 1 pg/µL reserpine in 75:25 methanol :water and 5 mM ammonitun acetate, at 5 minute intervals.

Using the 609 Da mass chromatogram, calculate the peak to peak, 1 SD signal to noise ratio for each peak. The average signal-to-noise value should be >100.

 

 

Groupe de produits: MS

Back to Top
part-of-labexchange-group
Recherche propulsée par ElasticSuite
Labprocure