Shimadzu LC 10A
Objektnummer | B00015390 |
---|---|
Numéro d'identification | 015390 |
Nom de l'objet | Shimadzu LC 10A |
Statut | Archiv |
Statut, conditions de livraison et de paiement
Vérification des appareils
Les appareils d’occasion sont vérifiés par Labexchange Service GmbH avant la livraison. Vous recevez des appareils entièrement fonctionnels.
Délai d'expédition
Les délais de livraison indiqués sont les plus rapides pour l’article en cause. Les délais de fait peuvent varier au cas par cas. Les délais de livraison définitifs sont indiqués dans la confirmation de commande.
Nous offrons des livraisons collectives par principe. Le délai de livraison s’oriente à l’article avec le délai de livraison le plus long. Une livraison partielle est possible par prix additionnel.
Méthodes d'expédition
Courrier, agences d'expédition, autocueillette, livraison par flotte de Labexchange
Conditions de livraison
Prix plus frais d’expédition. Les frais d’expédition indiqués sont à prévoir. Dérogations éventuelles sont possibles.
Si les coûts de transport ne sont pas spécifiés, s'il vous plaît demander séparément les frais de transport. Les frais de transport et d'emballage indiqués se réfèrent à l'itinéraire de transport le moins cher et sont sujets à des augmentations de coûts imprévues. En raison d'événements imprévisibles, les tarifs de transport et les délais de livraison peuvent changer à tout moment et doivent être adaptés à la situation actuelle. Incoterm codage selon les Incoterms 2010: Pour personnes qui viennent chercher les dispositifs elles-mêmes: EXW, pour les expéditions par voie maritime: CFR, par avion: CPT, d'autres expéditions: DAP. Remarque: Nous n'établissons pas des preuves préférentielles/EUR1. Dans le cas d’un enlèvement par vos soins/EXW de pays à l’intérieur ou à l’extérieur de la Union européenne, nous devons conserver 16% de TVA d’acheteur comme dépôt de garantie, jusqu’à ce que nous ayons reçu l’attestation de reception/la prevue de livraison.
Modalités de paiement
Nous n’acceptons pas le paiement par lettre de credit, PayPal, etc. Dans tous les cas le montant est payable sans déduction. Jusqu’au paiement complèt l’équipement reste notre propriété. Un escompte n’est pas accordé.
Pays |
Modalités de paiement possible |
Remarque |
DE, AT, CH |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
NL, BE, LU |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
Autre pays |
Prépaiement, par carte de credit |
|
Nos conditions de vente, de livraison et de paiement sont en vigueur. Vous pouvez télécharger les documents ici.
La vente intermédiaire nous est réservée.
Défintion des statuts
Tous articles sont d’occasion, sauf si explicitement défini comme « appareil neuf ».
Statut |
Condition |
Remarque |
Immédiatement disponible |
Occasion |
L’article a été déjà entièrement vérifié et peut être envoyé directement à vous. |
En stock |
Occasion |
L'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels. |
Publié |
Occasion |
L’article est toujours au l’offreur. Nous achetons, vérifions et en fin livrons l’article après votre commande. Le certificat de fonctionnement ainsi que le rapport de service sont inclus à la livraison. |
Appareil neuf |
Neuf |
C’est un dispositif neuf. L’article n’est pas utilisé et neuf d’usine. En ce qui concerne des article neufs, la garantie du fabricant est valable. |
Labprocure |
Occasion |
Responsable du contenu de l‘offre d’appareil est la société Labprocure GmbH, comme annonceur. Labprocure assume la responsabilité des offres annoncées ici ainsi que des photos et des textes d’offre inclus. Labprocure GmbH, Bruckstraße 58, 72393 Burladingen. |
Manufacturer: Shimadzu
Model: LC 10A
The following illustrations and descriptions are model-related and taken from brochures.
They do not reflect the scope of delivery of the system.
The exact scope of delivery can be found in the offer text.
The LC-10AD is a dual piston pump designed to improve accuracy and sensitivity when using a high performance liquid chromatograph.
In addition to a pump, an automatic or manual injector, column, injector holder, and detector are required for a high-performance liquid chromatography system. All these devices are supplied as additional special accessories.
Please note that these operating instructions are solely limited to the operation of the LC-10AD and the important accessories. As far as the operation of the optional accessories is concerned, please refer to the operating instructions for the respective devices.
characteristic
1. Ultra-low flow pulsation solvent delivery and highly accurate gradient delivery
Compared with conventional models, the strength of the flow pulsation has been significantly reduced and the pulsation cycle is noticeably shortened. This was achieved by reducing the outflow volume to a micro volume of 10 liters per piston stroke and by using a high-speed piston. These properties allow the use of pulsation-sensitive detectors (eg differential refractometers and electrochemical detectors) in the high-sensitivity range. In addition, extremely precise gradient delivery is possible in the semi-micro volume range.
2. Variety of functions for gradient delivery
Two methods, the low and the high pressure method, are available for gradient delivery. The high-pressure gradient method is extremely accurate and has minimal delay, while the low-pressure gradient method allows solvent delivery with up to four liquids at low cost.
In addition, the control of these gradient delivery methods can be performed with two different system configurations. Either use the SCL-10A system controller or control the gradient delivery from the LC-10AD (without using a system controller).
3. Use of buffer solutions
The automatic flushing device on the back of the piston seal automatically cleans the piston. When using a high salt concentration buffer solution as the mobile phase, this device effectively prolongs the life of the piston seal.
Specifications of the LC-10AD unit
1. Pump: Micro volume double piston pump (approx. 10 l/stroke)
2. Solvent Delivery Methods: Delivery at a constant flow rate or
with constant pressure.
a) Delivery with constant flow rate:
Flow Velocity Range:
0.001 - 5 ml/min (10 - 400 bar)
5,001 - 9,999 ml/min (10 - 200 bar)
Compliance with the set flow rate:
Within 2% or 2 l/min, whichever is greater
(0.01 - 5 ml/min, 10 - 400 bar, with water and room temperature of 20°C) except for areas of low pressure gradient delivery
Flow Velocity Accuracy: Within 0.3% (0.1 - 5 ml/min, 10 - 400 bar with water and room temperature of 20°C)
b) Feeding with constant pressure:
Pressure input range: 10 - 400 bar (at 1 bar intervals)
Maintaining the set pressure: Less than 10% or 10 bar, whichever is greater.
3. Pressure limit: high/low pressure
4. Pulsation dampener: Internal capacity of about 200 l.
5. Materials in contact with solvent: SUS 316 (stainless steel), Ruby, Sapphire, Teflon 9 9 graphite annealed, Hastelloy Ce, PEEK, Kahez KelF
6. Suction filter: Sieve size 10
7. Line filter: Sieve size 2, capacity approx. 200 1
Time program: Flow rate, pressure, EVENT and LOOP (program repetition). A total of 10 files and 320 steps.
9. Pressure reading accuracy: 2% or 5 bar, whichever is greater.
10. Piston seal cleaning flow line: Automatic cleaning is made possible by connecting the optional automatic rinsing device.
11. Dimensions: 260 x 150 x 420 (width x height x depth), but protruding components are not included.
12. Weight: 11kg
13. Operating temperature range: 5 - 35°C
14. Operating voltage: P/N 228-25000-93 : 200 - 250 VAC,
100W
High Pressure Gradient Specifications
1. SCL-10A controller
1) Number of mixed solvents: 2 or 3
2) Gradient profile: linear, step and exponential functions; they can consist of several steps.
3) Number of program steps: 20 files and 400 steps in total
4) Program time: 0.01 - 9999.9 min
5) Mixing ratio input area: 0 - 100% (in 0.1% steps)
6) Compliance with the entered mixing ratio: 1% (0 - 100%, 0.1 - 3m1/min, 10 - 400 bar, with a water - acetone mixture)
2.LC-10AD
1) Number of mixed solvents: 2
2) Gradient profile: linear and stairs; they can consist of several steps.
3) Number of program steps: 10 files and 320 steps in total
4) Program time: maximum 999.99 min (in 0.01 min increments)
5) Mixing ratio input area: 0 - 100% (in 0.1% steps)
6) Compliance with the entered mixing ratio: 1% (0 - 100%, 0.1 - 3 ml/min, 10 - 400 bar, with a water - acetone mixture)
Low Pressure Gradient Specifications
1. SCL-10A controller
1) Number of mixed solvents: up to 4
2) Gradient profile: linear, step and exponential functions; they can consist of several steps.
3) Number of program steps: 20 files and 400 steps in total
4) Program time: 0.01 - 9999.9 min
5) Mixing ratio input range: 0 - 100% (in 0.1% increments)
6) Applicable flow rate range: 0.1 - 9.99 ml/min
2.LC-10AD
1) Number of mixed solvents: up to 4
2) Gradient profile: linear and stairs; they can consist of several steps.
3) Number of program steps: 10 files and 320 steps in total
4) Program time: maximum 999.99 min (in 0.01 min increments)
5) Mixing ratio input area: 0 - 100% (in 0.1% steps)
6) Applicable flow rate range: 0.1 - 9,999 ml/min