Malvern Zetasizer 1000
Objektnummer | B00017771 |
---|---|
Numéro d'identification | 017771 |
Nom de l'objet | Malvern Zetasizer 1000 |
Statut | Archiv |
Statut, conditions de livraison et de paiement
Vérification des appareils
Les appareils d’occasion sont vérifiés par Labexchange Service GmbH avant la livraison. Vous recevez des appareils entièrement fonctionnels.
Délai d'expédition
Les délais de livraison indiqués sont les plus rapides pour l’article en cause. Les délais de fait peuvent varier au cas par cas. Les délais de livraison définitifs sont indiqués dans la confirmation de commande.
Nous offrons des livraisons collectives par principe. Le délai de livraison s’oriente à l’article avec le délai de livraison le plus long. Une livraison partielle est possible par prix additionnel.
Méthodes d'expédition
Courrier, agences d'expédition, autocueillette, livraison par flotte de Labexchange
Conditions de livraison
Prix plus frais d’expédition. Les frais d’expédition indiqués sont à prévoir. Dérogations éventuelles sont possibles.
Si les coûts de transport ne sont pas spécifiés, s'il vous plaît demander séparément les frais de transport. Les frais de transport et d'emballage indiqués se réfèrent à l'itinéraire de transport le moins cher et sont sujets à des augmentations de coûts imprévues. En raison d'événements imprévisibles, les tarifs de transport et les délais de livraison peuvent changer à tout moment et doivent être adaptés à la situation actuelle. Incoterm codage selon les Incoterms 2010: Pour personnes qui viennent chercher les dispositifs elles-mêmes: EXW, pour les expéditions par voie maritime: CFR, par avion: CPT, d'autres expéditions: DAP. Remarque: Nous n'établissons pas des preuves préférentielles/EUR1. Dans le cas d’un enlèvement par vos soins/EXW de pays à l’intérieur ou à l’extérieur de la Union européenne, nous devons conserver 16% de TVA d’acheteur comme dépôt de garantie, jusqu’à ce que nous ayons reçu l’attestation de reception/la prevue de livraison.
Modalités de paiement
Nous n’acceptons pas le paiement par lettre de credit, PayPal, etc. Dans tous les cas le montant est payable sans déduction. Jusqu’au paiement complèt l’équipement reste notre propriété. Un escompte n’est pas accordé.
Pays |
Modalités de paiement possible |
Remarque |
DE, AT, CH |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
NL, BE, LU |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
Autre pays |
Prépaiement, par carte de credit |
|
Nos conditions de vente, de livraison et de paiement sont en vigueur. Vous pouvez télécharger les documents ici.
La vente intermédiaire nous est réservée.
Défintion des statuts
Tous articles sont d’occasion, sauf si explicitement défini comme « appareil neuf ».
Statut |
Condition |
Remarque |
Immédiatement disponible |
Occasion |
L’article a été déjà entièrement vérifié et peut être envoyé directement à vous. |
En stock |
Occasion |
L'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels. |
Publié |
Occasion |
L’article est toujours au l’offreur. Nous achetons, vérifions et en fin livrons l’article après votre commande. Le certificat de fonctionnement ainsi que le rapport de service sont inclus à la livraison. |
Appareil neuf |
Neuf |
C’est un dispositif neuf. L’article n’est pas utilisé et neuf d’usine. En ce qui concerne des article neufs, la garantie du fabricant est valable. |
Labprocure |
Occasion |
Responsable du contenu de l‘offre d’appareil est la société Labprocure GmbH, comme annonceur. Labprocure assume la responsabilité des offres annoncées ici ainsi que des photos et des textes d’offre inclus. Labprocure GmbH, Bruckstraße 58, 72393 Burladingen. |
manufacturer : Malvern
model : Zetasizer 1000
annotation : Dokumente engl.
The following illustrations and descriptions refer to the instrument model and are drawn from brochures. They do not represent the scope of delivery. Please refer to the text of the offer for the exact scope of delivery.
Technicla Specification
Model Zetasizer Particle Size and Zeta Potential Analyser.
Laser 10mW max. output He-Ne; 633nm.
Computer, minimum IBM PC-AT compatible, Pentium 166MHz processor, 32MByte RAM, specification 30 Mbytes free disk space, one free RS232C communications port,
3.5" disk drive, CD-ROM drive.
Windows 2000 or NT sp6b installed. 800*600 resolution 256 colour monitor (2 Mbytes video card).
Notes: 1. A laptop computer is suitable,
2. Use with a Titrator or autosampler requires two free RS232C communication ports.
Data display Graphical and tabular formats for particle size, electrophoretic
mobility and zeta potential distributions; graphical plots of any two parameters e.g. mobility vs. pH, particle size vs. zeta potential.
Communications Full bi-directional RS232C standard.
Printer Any Windows compatible printer.
Power requirements 100 -260 V; 50/60 Hz.
Maximum 720VA power consumption.
Size range Zetasizer 2nm - 3 microns approx. (Sample and source dependent).
1000/3000
Scattering angle for Zetasizer 1000 90 degree fixed angle.
size analysis Zetasizer 30 00 12 and 90 degrees.
Electrophoresis Applicable size range, 5nm - 30 microns (Sample dependent).
Mobility range ±10 m 2 s -1 V -1 x10 -8 , typical, no maximum exists.
Operating mode Heterodyne zetapotential, Homodyne or self beat size mode.
pH range 2 - 12.
Applied voltage 400V max.
Field strength (Max.) 80 V/cm.
Duty cycle operation limits heating in high conductivity media.
Cells Zetasizer 1000 series Supplied with disposable polystyrene and
glass cuvettes.
Zetasizer 2000 Standard capillary electrophoresis cell. Optional parallel plate cells.
Zetasizer 3000 series Standard capillary electrophoresis cell. Optional parallel plate cells. Supplied with disposable polystyrene and glass cuvettes for size measurement.
Automatic settings Automatic setting and sensing of applied voltage, temperature and
cell type.
Modulator 125, 250, 500 or 1000Hz frequency. Fixed heterodyne optical
system.
The optical unit
The Zetasizer optics unit can be divided into three areas for the purposes of this description. These are; the front panel (1), the sample area (2) and the rear panel (3 ) . Each of these are discussed below.
Front panel
Two LEDs are situated on the front panel (1). The far left LED glows orange to indicate that power is on. The right hand LED will glow green shortly after the instrument is switched on to indicate that the instrument is ready to make a measurement, it will flash red when a measurement is being made.
Sample area
The illustration below identifies the features of the sample area.
(1) Hinged sample compartment cover
To access the sample compartment the cover must be raised. There is a mechanical laser interlock connected to the cover and an electrical interlock to cut off the power supply to the cell. Consequently, laser radiation is inaccessible as soon as the cover is opened. When the cover is lowered completely the laser will illuminate the sample.
(2) Pinhole
Dependent on the system ordered, systems incorporating size measurement (i.e. Zetasizer 1000 and 3000 series) are supplied with a 200 micron pinhole fitted. This should not be changed in normal operation.
(3) Sample valves
The sample valves control the flow of sample through the cell.
(4) Size cell
The sizing cell is used to make size measurements. This is only applicable to the Zetasizer 1000 and 3000 series systems. The cell is fitted with a thermal cover.
Plastic or quartz cuvettes can be used. The type chosen will be dictated by chemical compatibility with the sample and dispersant. It is strongly recommended that tops are fitted to the sample cuvette prior to insertion into the cell holder. This is to prevent spillage into the sample holder and better thermal stability. In the event of a large spillage a service visit by a Malvern representative is recommended.
For measurements done above ambient temperature it is recommended that the insulating thermal cover is fitted.
(5) Zeta potential capillary cell
The capillary cell is used to make zeta potential measurements.
(6) Electrode connectors
These electrodes are connected to the electrode blocks once the capillary is fitted. The grey electrode wires are colour coded. The yellow connector is clipped to the yellow electrode at the rear of the cell and obviously the red connector on the red coded electrode. Connectors are a simple push fit, however to remove them, the clip should be pushed sideways rather that pulled.
(7) Sample in/out connectors
The sample in/out connectors are used to inject the sample into the capillary and sizing flowcell.
(8) Aqueous / non Aqueous dip cell readback connector
The readback lead from the Aqueous / non Aqueous Cells is connected to this connector.
Rear panel
Use the diagram below to identify the features on the rear panel and their function.
(1) On/off switch
This is the main power switch for the instrument.
(2) Main fuse holder
The main instrument fuse (only to be replaced by the supervisor or a Malvern representative).
(3) Mains power socket
The mains power supply is connected to here.
(4) Detector output test connector (Service personnel only)
This connector is only used by Malvern Service personnel for testing the detector output. The user should never use this connector.
(5) Computer COM1 connector
This connector is connected to the computer RS232, COM1, I0I0 or Serial port (depending on computer).
(6) External link (Service personnel only)
This connector is only used by Malvern Service personnel. The user should never use this connector.
(7) Aux. output
This port is used to connect the MPT1 Autotitrator Accessory to the instrument. Details of the connections will be found in the relevant Accessory manual.
(8) Auxiliary fuses
Fuses for Accessory options. Details of these fuses will be found in the relevant Accessory manual.