Leybold OMS 3000/M
Objektnummer | B00017510 |
---|---|
Numéro d'identification | 017510 |
Nom de l'objet | Leybold OMS 3000/M |
Statut | Archiv |
Statut, conditions de livraison et de paiement
Vérification des appareils
Les appareils d’occasion sont vérifiés par Labexchange Service GmbH avant la livraison. Vous recevez des appareils entièrement fonctionnels.
Délai d'expédition
Les délais de livraison indiqués sont les plus rapides pour l’article en cause. Les délais de fait peuvent varier au cas par cas. Les délais de livraison définitifs sont indiqués dans la confirmation de commande.
Nous offrons des livraisons collectives par principe. Le délai de livraison s’oriente à l’article avec le délai de livraison le plus long. Une livraison partielle est possible par prix additionnel.
Méthodes d'expédition
Courrier, agences d'expédition, autocueillette, livraison par flotte de Labexchange
Conditions de livraison
Prix plus frais d’expédition. Les frais d’expédition indiqués sont à prévoir. Dérogations éventuelles sont possibles.
Si les coûts de transport ne sont pas spécifiés, s'il vous plaît demander séparément les frais de transport. Les frais de transport et d'emballage indiqués se réfèrent à l'itinéraire de transport le moins cher et sont sujets à des augmentations de coûts imprévues. En raison d'événements imprévisibles, les tarifs de transport et les délais de livraison peuvent changer à tout moment et doivent être adaptés à la situation actuelle. Incoterm codage selon les Incoterms 2010: Pour personnes qui viennent chercher les dispositifs elles-mêmes: EXW, pour les expéditions par voie maritime: CFR, par avion: CPT, d'autres expéditions: DAP. Remarque: Nous n'établissons pas des preuves préférentielles/EUR1. Dans le cas d’un enlèvement par vos soins/EXW de pays à l’intérieur ou à l’extérieur de la Union européenne, nous devons conserver 16% de TVA d’acheteur comme dépôt de garantie, jusqu’à ce que nous ayons reçu l’attestation de reception/la prevue de livraison.
Modalités de paiement
Nous n’acceptons pas le paiement par lettre de credit, PayPal, etc. Dans tous les cas le montant est payable sans déduction. Jusqu’au paiement complèt l’équipement reste notre propriété. Un escompte n’est pas accordé.
Pays |
Modalités de paiement possible |
Remarque |
DE, AT, CH |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
NL, BE, LU |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
Autre pays |
Prépaiement, par carte de credit |
|
Nos conditions de vente, de livraison et de paiement sont en vigueur. Vous pouvez télécharger les documents ici.
La vente intermédiaire nous est réservée.
Défintion des statuts
Tous articles sont d’occasion, sauf si explicitement défini comme « appareil neuf ».
Statut |
Condition |
Remarque |
Immédiatement disponible |
Occasion |
L’article a été déjà entièrement vérifié et peut être envoyé directement à vous. |
En stock |
Occasion |
L'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels. |
Publié |
Occasion |
L’article est toujours au l’offreur. Nous achetons, vérifions et en fin livrons l’article après votre commande. Le certificat de fonctionnement ainsi que le rapport de service sont inclus à la livraison. |
Appareil neuf |
Neuf |
C’est un dispositif neuf. L’article n’est pas utilisé et neuf d’usine. En ce qui concerne des article neufs, la garantie du fabricant est valable. |
Labprocure |
Occasion |
Responsable du contenu de l‘offre d’appareil est la société Labprocure GmbH, comme annonceur. Labprocure assume la responsabilité des offres annoncées ici ainsi que des photos et des textes d’offre inclus. Labprocure GmbH, Bruckstraße 58, 72393 Burladingen. |
Firma: Lebold
Nachfolgende Abbildungen und Beschreibungen sind modellbezogen und aus Prospekten entnommen.
Sie geben nicht den Lieferumfang des Systems wieder.
Den exakten Lieferumfang entnehmen Sie bitte aus dem Angebotstext.
The system consists basically of:
- the optomechanical part OMS 3000 M (rack module with chopper, lamp, monochromator, detector, etc.)
- the electronical part OMS 3000 E (indication, operation and Signal processing)
-
the feed throughs at the vacuum
chamber with the light fibers
What OMS 3000 makes possible
Optical thin-film coatings are becoming increasingly important in industrial processes, as well as throughout the entire field of "high technology".
Various applications require high-precision specialized films or multilayer coatings for precise functions such as:
- Transmittance
- Reflectance
- Absorption
- Scattering
- Resistive to high temperature and moisture
- Abrasion resistance, adhesion
Multilayer coating systems used for beamspitters, color conversion filters, bandpass, and heat protection filters, and for coldlight and laser mirrors, have to be produced to extremely tight tolerances
The tight specifications which are required for modern laser components and precision optics can only be met by using precise optical monitoring methods. The optical monitoring system has to supply a high signal resolution over a large measuring interval, excellent reproducibility and longterm stability. Besides this, the optical monitoring system should be user-friendly and offer easy maintenance of all components. A straigtforward light measuring instrument with an ACamplifier is no longer sufficient for up to date requirements.
Thus, LEYBOLD has developed the OMS 3000, a new computer-based process photometer. It allows the precise cut off of the deposition of layers through the measurement of the changing reflectance or transmittance of separate test glasses or of the substrates themselves.
Major features
- Low long-term photometric drift
- Simple maintenance
- Dual-beam design based on flexible fiber optics
- High signal resolution
- Automatic setting of amplifier gain and calibration of reflectance and transmittance
- Display or results in units of percentage transmittance or reflectance with a resolution of 0.01 or 0.001 % respectively
- The operator feeds the relevant process parameters into the computer
- Automatic determination of related instrumental parameters
- The expected photometric curve is computed and analyzed in advance
- The trigger point (cut off) is corrected in real time
- Full support of all standard monitoring strategies
- Movings substrates measurable in intermittent mdoe
- Material's refractive index is automatically determined and displayed upon passing the A/4-turning point for single-layer coatings
- The spectral curves of reflectance or transmittance are measurable between two layers.
Where the OMS 3000 is used
Application areas
The OMS 3000 performs reflectance or transmittance measurements.
A major application is the real>time process control during the deposition of optical coatings. Both coninuous measurements on stationary substrates and intermittent measurements on moving substrates positioned on rotary carriers are possible. The monitoring software ensures reliable automatic film>thickness cut off during the deposition process. Computation of cut>off conditions and optimal setting of instrumental parameters (amplifier gain, time constant etc.) are performed automatically.
Real time trigger>point correction provides for high precision of layer thickness and excellent reproducibilities.
A stepper>motor controlled monochromator integrated into the standard instrument permits accurate measurements of complete reflectance or transmittance spectra. This leads to the following set of application areas:
- Reflectance or transmittance spectra taken under vacuum and in the air can be compared. Curves obtained may be edited (via a RS 232 C serial interface) by a plotter accepting standard HP>protocols.
- During a coating process the spectral curves can be measured between the deposition of two layers. The resulting data may be used for performing an on>line optimation, for this purpose the OMS 3000 can communicate with a PC via its RS 232 C serial interface.
- Quality control in production. Measured spectral curves may be processed by PC and compared with the given specifications. Where the OMS 3000 is used
- Film checking and monitoring in inline coating systems. The excellent long-term stability of the OMS 3000 allows it to operate continuously over long time periods without recalibration.
- A specially developed measurement head equipped with an integrating sphere yields stable reflectance measurements on moving substrates.
Method of measurement
The OMS 3000 is a double-beam
photometer built in lock-in technology. It features light fibers to obtain inaccessible measuring points.
Fig. 1.1: Double beam measuring principle with fiber optic
1 Vacuum chamber
2 Feed through
3 Light fibers
4 Chopper
5 Lamp
6 Light barriers
7 Chopper motor
8 Stepping motor (for monochromator)
9 Grating monochromator
10 Detector
Transmission and reflection measurements can be performed in intermittent and in stationary mode.
Technical data
Optical Data
Light Sources
Halogen lamp, 12V/50W, approx. 1000 hours operating life, 400 nm - 2,400 nm useful wavelength range
Deuterium lamp (not yet available), 30W, approx. 1,500 hours operaing life, 200 nm - 400 nm useful wavelength range
Grating Monochromators
Stepper-motor controlled for use over 6 operating ranges
Model Blocking Wavelength
filter Range
SMC 1-02 - 200-400 nm
SMC 1-03 - 400-800 nm
SMC 1-04 - 450-900 nm
SMC 1-04 RG 610 600-1100 nm
SMC 1-05 Si 1000-1800 nm
SMC 1-06 Ge 1700-2400 nm
Linear Dispersion (Standard)
4.5 nm/mm in the UV spectral range, 6nm/mm in the VIS-spectral range, 1 0 to 30 nm/mm in the NIR-spectral range
Detector
Silicon (standard), 400 - 1,100 nm useful wavelength range
Lead sulfide (optional), 1,100 - 2,400 nm useful wavelength range
Photomultiplier (not yet available) (optional) 200 - 900 nm useful wavelength range
Light Coupling
Fiber-optic bundle, 2.3 mm dia., NA= 0.22, acceptance angle = 25.5°, Measurement ranges: UV-fibers: 200-1200 nm, NIRfibers: 400-2400 nm
Optical Feedthrough with Coupling
Optics
Available on special order
Signal Resolution
0.01 % referred to 100 % R or T for R or T > 10 %
0.001 % referred to 100 % R or T for R or T < 10 %
Noise/Signal Ratio
Dependent upon wavelength range and system signal yield, standard is the same as signal resolution
Long-Term Stability
1 % per week instrumental drift
Chopper Frequency 13 Hz
Interfacing
Data Entry Keypad with 8 keys
Display
5" monitor screen
Host-Computer Interfaces
RS 232 C and multibus-compatible bus interface
Recorder Outputs
0 - 10 V corresponding 0 - 100 % R or T
0 - 10 V with programmable resolution
External Control and Processing Parallel interface with three potential free digital inputs and four potential free digital outputs for integration into a "nonintelligent" automatic
Electrical Supply
OMS 3000 M OMS 3000 E
Voltage 220 V ± 10 % 220 V ± 10 %
Frequency 50/60 Hz 50/60 Hz
Power Consumption 150 VA 70 VA
Dimensions
OMS 3000 M OMS 3000 E
Height 265 mm 133 mm
Width 325/295 mm 450 mm
Depth 500 mm 350 mm
Weight 23 kg 8 kg