Biolog Microlog 1
Objektnummer | B00014862 |
---|---|
Numéro d'identification | 014862 |
Nom de l'objet | Biolog Microlog 1 |
Statut | Archiv |
Statut, conditions de livraison et de paiement
Vérification des appareils
Les appareils d’occasion sont vérifiés par Labexchange Service GmbH avant la livraison. Vous recevez des appareils entièrement fonctionnels.
Délai d'expédition
Les délais de livraison indiqués sont les plus rapides pour l’article en cause. Les délais de fait peuvent varier au cas par cas. Les délais de livraison définitifs sont indiqués dans la confirmation de commande.
Nous offrons des livraisons collectives par principe. Le délai de livraison s’oriente à l’article avec le délai de livraison le plus long. Une livraison partielle est possible par prix additionnel.
Méthodes d'expédition
Courrier, agences d'expédition, autocueillette, livraison par flotte de Labexchange
Conditions de livraison
Prix plus frais d’expédition. Les frais d’expédition indiqués sont à prévoir. Dérogations éventuelles sont possibles.
Si les coûts de transport ne sont pas spécifiés, s'il vous plaît demander séparément les frais de transport. Les frais de transport et d'emballage indiqués se réfèrent à l'itinéraire de transport le moins cher et sont sujets à des augmentations de coûts imprévues. En raison d'événements imprévisibles, les tarifs de transport et les délais de livraison peuvent changer à tout moment et doivent être adaptés à la situation actuelle. Incoterm codage selon les Incoterms 2010: Pour personnes qui viennent chercher les dispositifs elles-mêmes: EXW, pour les expéditions par voie maritime: CFR, par avion: CPT, d'autres expéditions: DAP. Remarque: Nous n'établissons pas des preuves préférentielles/EUR1. Dans le cas d’un enlèvement par vos soins/EXW de pays à l’intérieur ou à l’extérieur de la Union européenne, nous devons conserver 16% de TVA d’acheteur comme dépôt de garantie, jusqu’à ce que nous ayons reçu l’attestation de reception/la prevue de livraison.
Modalités de paiement
Nous n’acceptons pas le paiement par lettre de credit, PayPal, etc. Dans tous les cas le montant est payable sans déduction. Jusqu’au paiement complèt l’équipement reste notre propriété. Un escompte n’est pas accordé.
Pays |
Modalités de paiement possible |
Remarque |
DE, AT, CH |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
NL, BE, LU |
Paiement par facture, prépaiement, par carte de credit |
Paiement par facture est possible pour clients professionnels. |
Autre pays |
Prépaiement, par carte de credit |
|
Nos conditions de vente, de livraison et de paiement sont en vigueur. Vous pouvez télécharger les documents ici.
La vente intermédiaire nous est réservée.
Défintion des statuts
Tous articles sont d’occasion, sauf si explicitement défini comme « appareil neuf ».
Statut |
Condition |
Remarque |
Immédiatement disponible |
Occasion |
L’article a été déjà entièrement vérifié et peut être envoyé directement à vous. |
En stock |
Occasion |
L'article est en notre stock, mais doit être vérifié avant la livraison par nos techniciens Vous recevez des articles entièrement fonctionnels. |
Publié |
Occasion |
L’article est toujours au l’offreur. Nous achetons, vérifions et en fin livrons l’article après votre commande. Le certificat de fonctionnement ainsi que le rapport de service sont inclus à la livraison. |
Appareil neuf |
Neuf |
C’est un dispositif neuf. L’article n’est pas utilisé et neuf d’usine. En ce qui concerne des article neufs, la garantie du fabricant est valable. |
Labprocure |
Occasion |
Responsable du contenu de l‘offre d’appareil est la société Labprocure GmbH, comme annonceur. Labprocure assume la responsabilité des offres annoncées ici ainsi que des photos et des textes d’offre inclus. Labprocure GmbH, Bruckstraße 58, 72393 Burladingen. |
Firma: Biolog
The following illustrations and descriptions are referring to the instrument model and are drawn from brochures. They are not representing the delivery volume. The exact delivery content you will find only in the offering text.
1.0 INSTRUMENT FAMILIARITY
1.1 Analog Display - 6" meter face.
1.2 Power Button - applies power to Instrument.
1.3 Test Tube Well - holds a round, 20 mm diameter test
tube. The recommended test tube size is 20 mm X 150 mm.
1.4 0% Transmittance Adjust - set screw for adjusting to
0%T when meter is turned off.
1.5 100% Transmittance Adjust - knob for adjusting to 100%T
with a blank reference test tube in the test tube well.
CALIBRATION
lf necessary, adjust set screw for full-scale 0% transmittance reading.
Turn meter on.
Insert blank refereg..ce test tube into test tube well and adjust transmittandeto 100%.
Instrument is now ready for Operation.
MEASUREMENT GUIDELINES
Avoid contaminating standards and sample solutions.
Use the same size test tubes for standards and samples. Perform a 100% transmittance adjustment for each test tube before adding a sample into it.
Test tubes are not optically uniform. Therefore, they should be oriented consistently in the light path so that the light beam passes through the saure portion of the tube.
BATTERIES
The turbidimeter uses a 9V rechargeable NiCd battery. The battery is charged whenever the plug-in power pack is supplied with power. The instrument need not be turned on for the recharger to work.
***CAUTION***
Failure to recharge the battery
could result in premature aging.
Use of the turbidimeter may continue while the battery is charging. The internal battery maintenance circuit will recharge the battery from a fully discharged state to a fully charged state in about 12 hours. It will not overcharge. No damage will result if the charger is connected indefinitely. The instrument may be stored with the charger connected.
BATTERY LIFE
A fully charged battery will operate the turbidimeter for about 8 hours. As the battery ages, the operating time may decline. End of life will usually occur alter over 1000 discharge/recharge cycles. When recharging does not result in significant operating time, the battery should be replaced.
REPLACING THE BATTERY
1. Turn power Off and disconnect power supply.
2. Remove the four rubber feet, from bottom of instrument.
3. Remove black shroud.
4. Locate battery holder on inside back panel.
5. Loosen the two screws on back panel of instrument to allow the battery to slicte out of bracket.
6. Remove battery snap from battery.
7. Replace defective battery with new battery.
CAUTION: Use only a NiCd rechargeable battery. Use of a Carbon-Zinc or Alkaline battery could result in the battery rupturing and subsequently causing harm to personel or equipment.
NOTE: Properly dispose of old batteries per local regulations.
8. Place battery snap on battery.
9. Place battery in bracket and tighten screws.
10. Test instrument for proper Operation.
11. Place bleck shroud back on instrument and reattach the rubber feet.
INSTRUMENTATION THEORY
The Biolog Turbidimeter uses a light emitting diode and 590 bandpass filter, which produces a monochromatic light at 590 nm. A current is developed by the photodiode proportional to the amount of light received. The current is then converted to a numerical value, shown as either absorbance or percent transmittance, depending on scale Chosen.
Power is applied to all circuitry by pressing the power button. A power jeck on the rear panel of the instrument is used to apply external power and recharge batteries.
A precision current regulator provides a stable, adjustable current to the LED lamp. The % Transmittance knob adjusts this current, allowing standardization to 100% T.
The silicon photodiode generates a current proportional to the light it receives, i.e., that passes through the test tube. This current is amplified and used to drive the meter movement.
The meter scale is calibrated in % Transmittance (linear with respect to transmitted light) and Absorbance (logarithmic with respect to transmitted light).
TROUBLESHOOTING GUIDE
SYMPTOM CORRECTIVE MEASURE
No response when Adjust % knob clockwise; if
sample is inserted still no response, make sure power switch is on, the instrument is plugged in, and/or battery is charged.
Non-linear Check all test solutions and
Standard Curves standards for expiration and/or contamination. Replace suspicious solutions and recheck meter.
Recheck standard range - a narrower range may be necessary to assure linearity.
Unstable Readings Make sure samples are completely stable and homogeneous. A sample that is changing or settling will result in unstable readings.
If all corrective actions fall, call your distributor for service.
SPECIFICATIONS
Wavelength 590 nm
Display 6" analog meter
Transmission 0-100%
Absorbance 0 - 2 A
Linearity ± 2%
Repeatability ± 0.5% T
Test Time 10 - 15 seconds minimum
Operating Temp.
Range +15 to +35°C
Storage Temp.
Range +5 to +50°C
Operating Relative
Humidity 20 to 70%
Storage Relative
Humidity 0 to 90% non-condensing
Bandwidth 10 nm
Wavelength Peak ± 2 nm
Size 41/2H x 8"W x 7D
Weight 1.9 lbs (0.86 Kg)
Power 9 V rechargeable NiCd battery or plug-in 9V, 100 mA power