Back to Top
Archive
Philips PU 9200x
Description:
Philips AAS PU 9200x. With Mercury Hydridsystem PU 3960x. Vapour System. PU 9390. Autosampler 9380x. 2xBurner. All lamps available at inquiry.
siehe Storeview
| Objektnummer | B00012371 |
|---|---|
| ID-number | 012371 |
| Object name | Philips PU 9200x |
| Status | Archiv |
Status, terms of delivery and payment
Verification of devices
The second-hand devices are verified by Labexchange Service GmbH before delivery. You are receiving only fully functional devices.
Dispatch time
The stated dispatch times are the shortest possible ones for each article. The effective dispatch times can vary. The effective dispatch times will be stated in the order confirmation.
As a matter of principle, we are offering collective deliveries. The shipping time is calculated based on the position with the longest lead time. A partial delivery is possible on explicit request.
Shipping methods
Parcel services, forwarding agencies, self-pickup, delivery by Labexchange fleet.
Delivery information
Prices exclude shipping costs. Stated shipping costs are to be expected. Deviations are possible. If transport costs are not specified, please ask separately for them.
The stated transport and packing charges apply to the most favorable route if transport and are to be understood as subject to verification due to unexpected cost increases. By reason of unpredictable events, cargo rates and delivery times can change at any time and therefore have to be adapted to the recent situation. Import formalities and possible customs charges will be borne by the purchaser. Incoterm coding according to Incoterms 2010: For persons who collect the devices themselves: EXW, for dipatch by sea: CFR, by air freight: CPT, other shipments: DAP. Note for international shipments: A proof of preference/EUR1 will not be issued by us. When self-collecting/ordering EXW from countries within or outside the European Union, 16% VAT will be retained as a deposit until we have received the corresponding confirmation of arrival/bill of delivery from the buyer.
Terms of payment
We do not accept payment by letter of credit, PayPal, etc. In each case the invoice amount is payable without deduction. Discount is not granted.
|
Country |
Possible payment methods |
Comment |
|
DE, AT, CH |
Payment by invoice, payment in advance, paymet by credit card |
Payment by invoice is only possible for corporate clients. |
|
NL, BE, LU |
Payment by invoice, payment in advance, payment by credit card |
Payment by invoice is only possible for corporate clients |
|
Other countries |
Payment in advance, payment by credit card |
|
Our General Terms of Sale, Delivery and Payment are valid and are available for download here.
The goods are offered subject to prior sale.
Definition of status
All articles are used articles, except an article is listed especially as a new device.
|
Status |
Condition |
Comment |
|
Immediately available |
Used | The article is fully functional and in impeccable condition. It can be shipped immediately. |
| In stock |
Used |
The article is on stock. Our service technicians will verify the article before delivery. You are receiving only a fully functional article. |
|
Published |
Used |
The article is still with the provider. After your order the article will be purchased and verified by us before being shipped to you. A certificate of operativeness as well as a service report are included in delivery. |
|
New device |
new |
The article is brand new and unused. Regarding new equipment the guarantee/warranty conditions of the corresponding manufacturer apply. |
|
Labprocure |
Used |
Labprocure GmbH, as the advertiser, is responsible for the content of this device offer. Labprocure assumes liability for the offers advertised here and for the photos and offer texts included. Labprocure GmbH, Bruckstraße 58, 72393 Burladingen. |
Firma: Philips
The following illustrations and descriptions are referring to the instrument model and are drawn from brochures. They are not representating the delivery volume. The exact delivery content you will find only in the offering text.
PU 9200X
Specification
OPTICAL
Light source: Philips data-coded hollow cathode lamps (HCLs) or suitable uncoded HCLs.
Lamp supply current: 0 to 20 mA.
Optics: Single beam or Stockdale high energy double beam (option).
Detector: Side window photomultiplier extended S-5 or S-20 multi- alkali wide range (option).
Wavelength scan range: 180 mm to 860 mm
rate: 0.1 to 100 nm/min.
Monochromator type: Ebert system with master holographic grating.
Focal length: 174 mm (approx.)
Aperture: f7.7 (nominal)
Grating area: 20 mm x 20 mm
Lines per mm: 1200
Blaze: 250 nm
Dispersion: 4.7 nm/mm
Spectral bandwidth: 0.2, 0.5, 1.0 nm
Limiting resolution: 0.2 nm
Wavelength accuracy: ±0.3 nm
Absorbance range: -0.150 A to 3.000 A (including Background Absorbance)
Sample signal: analogue output 1 V per 1 A
Background
signal: analogue output 1 V per 1 A
DATA DISPLAY
Presentation: 12 inch VDU Monochrome or Colour,
resolution 640 x 288.
Concentration readout: 0.001 to 9999
Concentration range: -9999 to 9999
Mass/Dilution correction: available
Corrected concentration range: -999.99E9 to +999.99E9
Corrected concentration readout: 0.001 to +999.99E9
Auto zero: 0.000 to ±0.002 A
Measurement time: 0.1 to 200 seconds (manual selectable)
Sample identification: 16 character alpha-numeric.
ANALYTE APPLICATION
Sample uptake rate:
(a) with 0.38 mm bore capillary: low (for normal use)
(b) with 0.5 nm bore capillary: higher (for better sensitivity)
Minimum sample size: 200 µl (for aliquot sample mode)
Calibration standards: Up to 5 standards and 1 blank
GAS REQUIREMENTS
Fuel flow range
air/acetylene flames: 0.8 to 2.3 l/min
all other flame types: 3.6 to 5.1 l/min
Oxidant: 8.0 l/min (minimum)
ELECTRONIC SYSTEM
Control System: Microprocessor Motorola 68000
PROMs Over 700K Bytes
RAMs 176K Bytes
Non Volatile RAM 16K Bytes
Keyboard: IBM PC Compatible
ACCESSORIES
Printer/computer socket: RS-232-C Epson compatible, baud rate 110 to 9600
Output to recorder: 1 V per 1 A
Digital balance interface: RS-232-C, 1200 baud even parity, 7 data
(RS 232/Spare) bits, 1 stop bit, configured as DTE.
Power output socket: 240 V or 120 V at 3 A
Furnace socket RS-232-C at baud rate of 4800
Vapour kit socket: 8 pin DIN (dedicated)
Electrothermal Atomiser
The PU9390X Electrothermal Atomiser is particularly useful for analysis of
very small volurnes where high measurement sensitivity in the parts per billion range is required. Samples can often be introduced into the electrothermal atorniser directly, reducing the need for chernical pretreatment.
PARAMETERS
Electrical power requirements: 200, 220, 240 V, 50 or 60 Hz, 30 A, 2 pole switched, single phase, 7.5 kVA
Permissible input voltage variation: ±10%
Ambient operating range: + 5°C to +40°C
Cooling water flow rate: Nominal 1.5 l/min, minimum 0.7 l/min
Flow pressure: Between 1.4 bar and 6.9 bar (20 lb/in2 to 100 lb/in 2 )
Maximum water temperature: 30°C
Number of available phases: 20
Atomisation temperature range: Ambient to 3000°C
Phase duration: 0 to 200 seconds
Ramp rate setting: 0 to 2000°C/second
Gas supplies: All gas connections must be set to a pressure of
1.1 ± 0.14 bar (15 ±2 lb/in 2 )
Inert purge gas or outer gas: Argon. Automatically selected during all furnace cycle phases. Flow rate: 3 L/min.
Inner gases:
Type 1 - air, fixed flow rate: 200 ml/min
Type 2 - argon/methane, fixed flow rate: 200 mL/min
Type 3 - argon, adjustable flow rates 0: 0 ml/min
1: 100 ml/min
2: 200 ml/min
3: 300 ml/min
Any one of the inner gases may be selected in any of the furnace cycle phases
Cool phase: Automatically selected phase at the end of the furnace cycle. Duration: 20 seconds
Power Supply Unit dimensions: 325 mm width x 395 mm height x 700 mm
Weight: depth
60 kg approx.
Cuvette types: Electrographite
Coated electrographite
Totally pyrolytic graphite
Probe type
Furnace Autosampler
The PU9380X Furnace Autosampler provides for a fully automatic analysis run of up to 48 samples when operating in the Furnace mode. It provides facilities for automatic matrix modifications, automatic standard additions preparation, automatic standard preparations and automatic sample dilution and reconcentration.
PARAMETERS
Carousel capacity: 48 sample cups
5 standard cups
3 large reagent cups
Sample/Standards cup: Volume - 2 ml
Material - polypropylene
Large cup: Volume - 24.5 Ml
Material - polyproplyene
Sampling system: 100 µl backfill syringe driven by a digital linear actuator
Reproducibility of sample volume: Better than 1% for 10 µl sample at 20°C
Accuracy of sample volume: + 0.5 µl
Ambient operating range: + 5°C to + 40°C
Wash bottle volume: 500 ml
Dimensions: 460 mm x 400 mm x 240 mm
Weight: 7 kg
Interconnections: To PU9390 Electrothermal Atomiser via 37-way ribbon cable and quick-fit gas line. To PU9385 Furnace Autoprobe via 7-way cable
Product group: Atomic absorption spectrometers (graphite furnace)
Questions?
Your Labexchange-Team will gladly help:
Christian Schmid
Laboratory and analysis, Laboratory equipment, Life science
Hubert Sauter
Spectroscopy, Chromatography
